Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11016612690 > Instructions

11016612690 Kenmore Washer - Instructions

All installation instructions for 11016612690 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016612690
1,291-1,305 of 1,374
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Noticed the agitator was not engagine and slipping

  • Customer: Wynona Roberts from Zwolle, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the softener mechanism off by pulling upward. Pried off the cap to the agitator with a screw driver then removed the center bolt with a nut driver. This did take a little effort since it had never been removed. Pulled the agitator out of the washer and cleaned all the parts of any soap residue accumulated over the years. Took the agitator and stood it on the floor placing both feet on the sides and pulled it apart. there is a ring inside that popped out along with the top part of the agitator and the small cogs fell out. Cleaned the two pieces and replaced the cogs, holding the main part upside down lowered the agitator bottom into place matching the four grooves after snapping the unit together slide the cog cover into place and gently replaced the agitator back into the washer and replaced the bolt tightly. Then snapped the softener attachment back into place. This required a good bit of pressure but snapped right into place. Done job. Saved a lot of money and a simple fix to a problem. Agitator now works just as it should, no slippage at all. Took about 30 min all together. You can go online to find installation directions for any brand washer that has a full size agitator.

Poor agitation

  • Customer: Mary from Cornwall, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Thurs. followed video directions, found the dogs to be defective and around 2 pm ordered dogs on line. To my surprise, on Friday around 11 am the dogs arrived. My husband installed them and the agitator is fine. I was so amazed at how quickly the dogs came. The machine was ready to go in less than a day. Thank you for your efficiency.

washer shook even when empty

  • Customer: Bernerd from Messena, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
replased all the springs

Washer tub leans to one side. ( Not centered.)

  • Customer: Edgar Seabrooks from Philadelphia, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the washer and removed the two screws from the control panel. Raised the control panel and disconnected the wire connector that connected to the top.Then removed the two spring clips that hold the cabinet to the back of the washer. removed the cabinet from the washer that exposed the frame of the washer. I then replaced the broken spring by pushing the tub of the washer as far as it would go and replaced the suspension spring. Then i reinstalled the cabinet and control panel. Everything worked okay. ood as new.

Intermittently the spin cycle would not empty the tub fully

  • Customer: Robert from York, PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off, let me say two things, this was my very first washer repair and the installation video was excellent.

Few things though ..... The first thing I noticed was the old parts I removed did not look that bad to me. I was starting to wonder if I was wasting my time. However, its apart now I'll continue on. I had a hard time properly seating the new couplings on either end correctly. They were VERY snug. What I ended up doing was getting a 20mm deep socket that fit perfectly onto the coupling and with a hammer gently, (and I underline gently) tapped the new parts into place. That fixed that problem. I also had some minor difficulty putting the cabinet back together, but nothing earth shattering. The cabinet fits on top of the frame, not under. And lastly, the small clips that hold the console on were not very reusable afterwards so I'll need to order a new set of them sometime.

All-in-all it was a fun repair that didn't take me too long and I saved quite a bit. I definitely would do it again if necessary. I've done about 5 loads of laundry since and everything seems to be working great so far.

- Bob

The washer was making noise and was leaving the cloth dripping wet at end.

  • Customer: Kenia from Orlando, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Before I even watch any partselect videos to do the repair, which I should of from the very beginning, ah, ja, ja, I had already disassembled the back panel "my way" to the washer and trouble shooting the washer with my wife's help. While she tilted the washer backwards, I looked under and we found that the noise was coming from in between top of the motor where the direct drive motor coupling is located and the clutch assembly came together which I learned along with names and functions after watching the partselect installation video. Nice! Once I received the part it took me like 45 minutes to put all back together. Took loose two screws to clips holding the motor, pulled motor of mounting bracket finding the broken piece, replaced it, recouped reinstalling motor onto the motor bracket, clip, clip the two little screws and walla, got the wife her washer back, at bed time rewards, peace of mind the rest was history... Thanks PartSelect for awesome videos and great customer service!

agitator,drive motor coupling,water pump 3 problems

  • Customer: judy from lawrenceville, GA
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch the you tube, and try to fix it by myself,to save money, and moving trouble.this is my first time fix a big machine like this,I was a little scare, but after I saw the youtube about how to fix the washmachine,I start to give a try.it take little bit more time for me to figure out ,but I finally made it. now I can wash my cloth now, and perhaps fix washmachine for my exrat income.( message sharing from an asian 58 yrs old lady, sorry for unable to show step by step due to English not very good)

Pumps but won't spin, leaks, top of agitator doesn't move

  • Customer: Kenneth from Talbott, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My repair was successful but was not as easy as some have reported. I needed to replace the coupler, but when I tried to remove the pump from the motor, the shaft was rusted and wouldn't budge. I pried and wiggled and used WD-40 to no avail. I ended up taking off the motor and pump as a unit. After replacing the coupler and reassembling the washer, the water pump leaked, probably as a result of all of the prying. To get the water pump off, I had to cut it into pieces, using a hack saw. Even when I got down to the end, I had to peel pieces of plastic off of the rusted shaft. I then had to file and sand the shaft to get it so that it would fit into the new pump. After putting the washer together again and running it through its cycles, I noticed that the top half of the agitator was not turning. I then ordered and installed the agitator repair kit. Through all of this, my orders were all correct and arrived in amazingly fast times. The videos were all very helpful. Even though it was a trial a times, I still saved a pile of money.

noise caused b y broken coupler between motor and transmission during "spin" and not spinning

  • Customer: John P from Brazil, IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed motor and broken coupler... installed new coupler and replaced motor. also removed pump to inspect for sock, etc. that that might have caused coupler to break.. ADVICE: Look for how-to video on YouTube first. Remove outer cabinet according to video by first removing the top control panel and then remove the outer cabinet which exposes the motor and pump. This way you will not have to tip machine up/back and work under it. This repair is made easily by first removing the outer cabinet.

Washer would not spin

  • Customer: Mark from McCall, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I followed the instructions from a YouTube video, just do a Google search for the make, model, and what the problem is and several videos will come up to pick from. Everything went just as described in the video, took about 10-min to take the motor out, a couple of minutes to replace the broken motor coupling, and another 10-min to put it back together - slick.

The tub would not spin during the spin cycle. I diagnosed that the door switch was functioning. And through some reading on the internet, found out it was the motor coupling. I replaced the clutch assembly strictly as preventative maintenance.

  • Customer: Jorma from Saint Cloud, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

Washer was not spinning.

  • Customer: DEREK from BARNHART, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
It was simple, unbolted the inside laid it down on its back, took four bolts how and replaced parts and reversed the steps. It was super easy and You guys was on top of the shipping. Wife is happy! saved $500!!!!!!

Motor Drive Coupling

  • Customer: Kenneth from Stoughton, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and that was a great help. I just entered my model number and selected the symptom. 61% of the time the drive coupling is the problem and it was. Ordered the part and got it the next day.

Tub was spinning only part time. Had to have help getting started

  • Customer: Kingsley from Ewing, IL
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Installed new clutch assembly and while I was at it replaced the Motor Coupling. Actually, I had a good time doing the repair. I am almost 80 years old, so had to have help laying the washer on backside. Got a small stool from which to work (back problems). The only thing I found the least bit difficult was reinstalling the retaining clip for the clutch assembly. The rest was a piece of cake. Were I to do the same repair now, it would take less than 30 minutes. Washer works like new now. Very proud of what I was able to accomplish. Of course, need to watch the repair video so you will know where to start.

Tub will not spin

  • Customer: Rick from Terre Haute, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After finding out the tub would not spin, I removed the washer to find broken pieces on the floor. I did a google search on my model number and found that the problem was the direct drive motor coupling (it matched the pieces on the floor). So, I watched the "how to" video and I followed the steps verbatim. I found the coupler missing and the plastic pieces on the drive broken. My order came in quickly (within 48 hours) and my washer was running in 20 minutes after receiving the package. It has been great ever since.
All Instructions for the 11016612690
1,291-1,305 of 1,374