11016612690 Kenmore Washer - Instructions

I watched the online video and followed the instructions,The only problem I had was getting the pump off the drive shaft it had rust built up,but it worked fine and was shipped as promised

I simply watched the video that was on YouTube for this site. It was dead on with my washer and super easy to do. The step by step was just awesome and easy to follow. The repair took just over an hour and I even cleaned the entire inside of this 12 year old washer which was pretty cruddy. The washer now spins great and works like new again. All for about $50. Thanks.

A word to the wise watch the repair video first guys and save an hour or 2 of aggrivation. I saved a couple hundred bucks instead of having the repair guys do it. It was easier than I thought. Machine runs like new again. Thanks Partselect. L.A.B. Rocland, Mass.

Disconnect washer from all connections and slide away from the wall far enough to give clearance where you can tilt the washer and lay on it's back. Remove old pump and replace with new pump, then reconnect washer to wall connections.

The repair was surprisingly simple. We followed the video and it was a simple fix :)

Popped off the fabric softener dispenser with a medium flat tip screwdriver. Removed the agitator screw with a 7/16 socket. Pulled out the agitator assembly. Pulled out the agitator cam assembly. Removed the 4 worn directional cogs/replaced with new ones. Reassembled in reverse order.

1) Slide retaining ring up 2) Remove old dispenser and toss out 3) Slip new dispenser on and lower retaining ring. Couldn't be simpler. I was surprised that I could actually get an exact replacement. Ordered it and two days later it was at my door. Great service!

Removed the agitator with a straight blade screw driver and then removed by hand the inner cap. Used a 7/16 socket with a long extension and ratchet and removed the agitator bolt. Once the bolt was removed I pulled agitator cam the contains the agitator dogs out of the Mover, Agitator. I replaced the worn agitator dogs with new ones and replaced everything and it worked fine. I did mark with a red Sharpie the direction the dogs were before removing them so I would replace them in the right direction. Very simple job that took less than 15 mins.

Pulled the machine away from the wall about 18 inches. Tip the washer back until resting stably against the wall. Used plies to remove two spring hose clamps. Use the screw driver to remove spring clips. Pulled old pump off and placed new pump on. Replace spring clips and hoses with clamps, and lowered the washer. Done!

the video pretty much told the whole story except I forgot to put the plastic collar piece on the new clutch when I put it back together so I got to do it twice. second time went even easier. Thanks for the video,it was great.

Well i'm an auto technician by trade so I just jumped right in without reading or watching anything, but I saw the video and in the days waiting for the part to show up I watched it. I would recommend everyone to watch the video because it is simpler than I made it.Easy repair any mechanical skills at all and you shouldnt ave any trouble.

I have never fixed a washer, but this website made it very easy. I watched the video so there were no surprises. I unpluged the machine and disconnected the water lines and removed the two back screws. The control panel and shell came of very easy, i then tipped the washer on to its backand removed the clamps holding the motor. The motor came out very easy and the coupler was a cinch to put in. After that I reversed the process and then the wife was happy she got her washer back, Iwas happy too because I didnt have to buy a new one.

The installation of the new parts was easy to put in. No problem after I figured out how to do it. The parts came really fast and we were very happy with the service.

Found input to gearcase deformed, so new coupler slipped under load. Replaced gearbox. All function restored, but machine banged harshly during spin. Discovered that "skid plate" had shifted during gearbox replacement. Remounted skid plate carefully with pry bar, correcting vibration.

replaced water pump