Models > 11016602691 > Instructions

11016602691 Kenmore Washer - Instructions

All installation instructions for 11016602691 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016602691
46-60 of 1,536
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Unbalanced and walk across the floor on spin cycle

  • Customer: James M from Elkhart IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 23 of 31 people found this instruction helpful
Part Select provided the problem determination information and the video on how to install the replacement parts. I ran into one problem, I could not remove the lock nut to remove the inter and outer tub. I should have bought the special wrench for $14, no local DYI or hardware store had the wrench. So, after examination I used a large screwdriver and wood block to lift the tubs up just enough to remove the old pads and replace with the new. The old pads showed only a wear, but was enough to spin the tubs off balance. The new tabs made the washing machine work like new. New washer $500, repair man $150, parts and information from Part Select $20 bucks, priceless.

lid switch plastic screw holes fatigued and broke - switch then did not close

  • Customer: Anthony from La Jolla CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 22 of 30 people found this instruction helpful
This is a machine I bought from Costco in 2001 - it has been very reliable and this was its first repair.
Getting the top off this washer requires a lot of disassembly. However, if you push the drum down on the right hand side of the machine, you can easily reach under the lid and remove the old switch. Mine had broken loose from its plastic mounts, so the lid plunger no longer activated it. Save the two screws that go through the washer top to secure the new switch.
I unplugged the electricity, reached under the top and pulled the old switch out. Its cables are enclosed in a stiff plastic hose with a slit down its length so you can pull the wires through the slit. You need to pull out around 6 inches of the wires. I then cut the wires to remove the old switch and next cut the wires on the new switch to the same length as the ones removed. Stagger the cuts about 1 inch so that the two joints will not be on top of each other. I stripped each end of the two wires, slipped shrink-wrap tubing (from radio shack) on to the new switch wires, then soldered the new switch wires to the existing wires back to the control center. I then slipped the shrink wrap over the soldered joints and shrank it with a match. Feed the joined wires back into the plastic tube and feed the switch under the washing machine rim. It takes a little maneuvering to get the switch aligned with the two screw holes in the top. Be sure the switch is pushed up into the lip opposite the screw holes - push the back end of the switch up into the lip before trying to align the front end of the switch with the screw holes. Align the screw holes with the switch holes, install the two screws and check that you hear the slight click of the microswitch if you push down a pencil into the interlock slot before you tighten everything up. Plug in the electricity and off you go!

Acting like it was unbalanced

  • Customer: Michael from Glenburn ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 19 of 21 people found this instruction helpful
I thought I would find broken springs but everything looked good. Comments and video very helpful.I figured springs must be stretched or worn out ,so for the money I figured worth a try. Insallation went well, washingmachine runs like a new machine. Much better than spending money on a new one. Thanks

Washing machine shook violently while on spin cycle

  • Customer: Tom from Bloomfield Hills MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 18 of 19 people found this instruction helpful
Disconnected the bracket screws that held the suspension springs in place - fed new springs into bracket and reattached. Local repairman told me that springs dont wear out, they break - wrong, they do lose their tension and thereby lose the ability to counterbalance the spinning load. Washing machine now spins like new - no wobble or shake.

valves allowed water to overflow during the rinse cycle, sometimes took forever to fill.

  • Customer: Sam from Robertsville MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 19 of 23 people found this instruction helpful
I removed the screws holding the control unit down, removed a couple at the rear,
Disconnected the electrical clip that plugs into the top, under the control unit.
This allows enough slack to pivot it ( the control unit) upside down and get it out of the way enough to remove the spring clips that hold the top to the back.
Popped out the two clips that hold the back to the top.
Pulled the back out, up until the plastic soap dispenser , (which is attached to the back) hits under the lip of the top.
This does not allow enough room to get to the valves.
I finally figured out you have to lift the entire top up high enough to clear the back while pulling it ( the back) out.
Disconnected the hose clamp, electric connectors, installed the new valves into the supplied mounting plate replaced the valves .
Re -connected the hose and electric connectors and re assembled the back.
The only problem I had was when one of the spring retainers that hold the back to the top popped off and fell inside the unit, which forced me to remove everything including the back bottom screws, which caused the sides to pop off, the mounting ears , which are attached to the back,
Took some finesse but finally retrieved the spring clamp and finished everything back together.
It was a bit tricky keeping the plastic gaskets between the back and the sides from falling inside as I reassembled it.
But all is well, and would have been more difficult without the expierence written by others who posted, on the site.
Thank you to all, for the help.
I hope my efforts will help someone else.

worn water pump and worn aggitator cogs

  • Customer: Chris from Morgan City LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 17 of 18 people found this instruction helpful
leaned and propped washing machine back to get access to pump, removed hose clamps and hoses,removed retainer clips, old pump was stuborn to remove but was able to pry off motor with screwdriver. sanded rust off metal shaft,put on new pump,replaced retainer clips, replaced hoses and clamps. set washer in upright position removed aggitator cap, used 7/16' socket with long extension,unscrewed bolt, pulled off aggitator sleave, removed cog unit, replaced cogs, put sleve back on and tightened bolt. I had the machine outside so I hooked up a water hose and an extension cord, put machine on small load and tested machine . worked like new. also when i finished the test I had noticed earlier that my hose screen had a mineral build up, cleaned that by lightly scraping and used little rust inhibitor that also tackles scales. total time was about 30 minutes. Wife is happy now and I was rewarded later.

Water control would only fill to Medium load then stopped altogether

  • Customer: Wayne from University City MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 23 people found this instruction helpful
I removed the screws holding the control board in place. Removed the knob on the front of the panel and then disconected the wires to the control. Then I took the old control off the board and inserted the new control. I attached the wire connectors to the new control and put the control panel back in place and fastened it with the screws. Last task was to replace the knob. The new control worked wonderfully with the first load of laundry. Piece of cake. Done in 5 minutes or less.

water leak at pump

  • Customer: oscar from missouri city TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 16 of 17 people found this instruction helpful
1. remove 2 hoses at pump using pliers to open hose clamps and sliding them out of the way.
2. remove 2 retainers holding pump with screwdriver.
3. remove old pump and install new pump
4. clamp pump using retaining clips
5. re-connect hoses

Top Half of Agitator would not function without appying sideways pressure

  • Customer: Donald from Fredericksburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 16 of 18 people found this instruction helpful
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remove black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...

Cog stripped causing agitator to not turn

  • Customer: Vicki from Houston TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 16 of 18 people found this instruction helpful
Removed top cap on agitator w/ flathead screwdriver. Removed protective cap over bolt and cog housing shaft. Used 7/16 deep socket w/ extension to remove bolt. Removed housing where stripped cogs were located. Cogs seated loosely in shaft housing no tools required to remove cogs. Replaced cogs in housing, made sure everything was lined correctly. re-inserted housing into shaft. ,screwed bolt, replaced caps and works like new.

The movers broke both water intakes off flush with the back of the machine

  • Customer: Dennis from Oak Island NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 16 people found this instruction helpful
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.

Water constantly dripped into washer when it was off.

  • Customer: MARK from MARION MA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 15 of 16 people found this instruction helpful
Turned off water and pulled power plug, Then unscrewed hot and cold hoses from washer.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Water valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 19 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Agitator was locked up

  • Customer: Roger from Palmyra IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 15 of 17 people found this instruction helpful
I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two hoses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger

Top half of the agitator was not turning.

  • Customer: Dennis from Avon NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 15 of 18 people found this instruction helpful
I just took the cap of the agitator off and the 3/8" nut was right there. I took it off with a socket, removed the top agitator, slid the assembled kit in , replaced the agitator and cap...that was it !!. These parts priced thrrough Sears were $77.00 plus S&H. Your price for the entire kit- less than $12.00 !! If you don't think that you can do this yourself, have your 7 year old child do it. Took me about 5 minutes. Great price and fast shipping. Thanks
All Instructions for the 11016602691
46-60 of 1,536