Models > 11016512691 > Instructions

11016512691 Kenmore Washer - Instructions

All installation instructions for 11016512691 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016512691
76-90 of 1,341
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washmachine wouldn't spindry

  • Customer: Chuck from South Holland IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 10 of 12 people found this instruction helpful
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

water leaking during run cycle

  • Customer: michael from weymouth MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 10 of 12 people found this instruction helpful
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer

Lid Switch broke had to replace.

  • Customer: Michael from Litchfield IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 9 of 9 people found this instruction helpful
The biggest problem for me was finding the screws to remove the control panel. First there are two screws on the top back side of the control panel, then there are plastic covers that have to be removed from both sides of control panel, then you can remove the screws at the base of the control panel. Set the control panel back, then remove the golden brackets that hold the cabinet to back of the washer. The whole cabinet will come forward with a little coaxing. (Remember to put the screws with the part you have removed to make sure you put them back in the same place.) Next remove screws that hold on the lid switch, remove wiring from clips, then replace with new switch, situate wiring in clips, position switch into place, screw into place. The cabinet is really hard to get back into place, be patient it may take a few tries. Once you get the cabinet in place, replace the golden brackets, then place the control panel where the screw holes line up and screw down, replace plastic sides, then replace the screws in the back side and your done.

The top lid switch failed so washer wouldn't run.

  • Customer: Katherine from Salem VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 9 of 9 people found this instruction helpful
Removed the valance by unscrewing nuts on top back and then removing side wings. The valance can be flipped up and hung over the back of the backsheet making sure not to damage clear hose. Then remove the old switch, wire and cut off the ground wire. Moount the new switch and make sure the wire is well back from the drum by tying to the old clip that held the old wire. Connect the ground to the body now under the valance. I found a hole there and screwed the ground terminal to it with a self taping screw.This procedure allows you to replace the switch without having to take the complete washer front body off.

water leaking from pump

  • Customer: michael from westmoreland city PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 13 people found this instruction helpful
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

improper or no hot water flow

  • Customer: Cynthia from Manchester MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 11 of 16 people found this instruction helpful
After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars instead of hundreds for a new machine.

washer did not agitate

  • Customer: Eric from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 11 of 16 people found this instruction helpful
popped thecap off removed the bolt, pulled agitator off replaced cogs(dogs) then put back together. works like new.whole time took about 10-15 min. saved my self 150.00 by not hireing repair man.

Wash machine, wouldn't spin dry the close. The pump still worked to drain the water.

  • Customer: Matthew from Albany MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 13 of 22 people found this instruction helpful
Unplug power from wall.
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from transmission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test

Agitator was barely agitating. Making a clicking noise.

  • Customer: Charmaine from Slidell LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 9 of 10 people found this instruction helpful
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.

Water level was low in the washer

  • Customer: Anil from Redmond WA
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 17 people found this instruction helpful
I had read many sites describing the issue of water level being low in the washer. Many people had suggested that changing the water level switch fixes the problem. So I ordered the part from PartSelect.com and it came promptly within a few days.

1. Disconnect the power to the washer.
2. Pull on the knob that controls the water level and remove it.
3. Remove the 2 screws on the bottom of the control panel.
4. Give the front portion of the control panel a small yank and pull it forward, around and upward. (It is hinged on the top, so it swings out)
5. Now you have access to the water level switch.
6. Press the clip and turn the switch a quarter of a turn and it will come off the panel.
7. Pull the wire connected to the switch and remove it.
8. Pull the air tube connected to the switch and remove it.
9. Use the new water level switch and reverse the process.
10. Plug the washer back in an everything works great!

Tub banged against the front of case during spin

  • Customer: Peter from Boca Raton FL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.

top agitator would not operate

  • Customer: Larry from Edgewood TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

my cold water did not run in the machine and it would not rinse

  • Customer: TONYA from DISTRICT HEIGHTS MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Darn thing hadn't "Agitated" for about 10 years!

  • Customer: Stephen from Cornwall NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 8 of 9 people found this instruction helpful
After removing the bolt (7/16" head), and using a pair of pliers to remove the 3-4 in deep "cup", it was immediately obvious how to assemble the new cup and pawls (ratchets).

Orienting the black "bearing" was not so obvious, but on closer inspection of the illustration, it became clear. The four "ears" of the bearing go closest to the pawls. The little tabs that are co-planar to the ears fit into the four grooves of the new cup.

And here's the trick (besides making REALLY, REALLY SURE how the pawls orient)--Soak the black bearing piece in hot water to soften it up, and let it slide over the cup better. If you don't, you risk breaking it. If you do, it slides over and "clicjs" into place, with the ears resting right against the bottom lip of the cup, capturing the pawls.

Installation back into the washer is obvious.

The thing works like a charm! It hasn't worked this well for a decade!

WILL NOT SPIN

  • Customer: Daniel from Temple TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 8 of 9 people found this instruction helpful
THIS IS A RELATIVELY NEW WASHER AND FAILED EARLY. MY PREVIOUS WHIRLPOOL WASHER LASTED 20 YEARS WITHOUT ANY REPAIRS.
1. FIRST INQUIRED ABOUT THE SPIN PROBLEM IN PARTSELECT. MACHINE WILL NOT SPING UNLESS MANUALY FORCED THEN IT WILL TAKE OFF BUT WEAK.
2.PARTSELECT SUGGESTED A CLUTCH PROBLEM. ORDERED THE PART THAT CAME FAST. WHEN I TRIED REMOVING THE SHAFT HUB WITH A HAMMER AND CHISEL IT WILL NOT GET LOOSE SO I OPTED ORDERING THE SPECIAL WRENCH TO LOOSEN THE TUB HUB.
3.I PUT THE MACHINE ON ITS BACK AND LOOSENED THE PUMP RETAINING CLIPS. DO NOT REMOVE THE HOSES FROM THE PUMP. MOVE THE PUMP AWAY FROM THE MOTOR SHAFT. REMOVE THE MOTOR ELECTRICAL CONNECTOR AND SET ASIDE.
4.REMOVE THE THREE BOLTS HOLDING THE GEARBOX-MOTOR ASSEMPLY AND PULL IT OUT OF THE TUB.
5.PUT THE ASSEMBLY ON A TOWELWITH SHAFT UP AND REMOVE THE SEPARATOR WASHER FROM THE OLD CLUTCH THAT IS SITTING ON THE GEARBOX. THEN REMOVE THE C-RETAINING CLIP FROM THE SHAFT.
6.PRY OUT THE WIRE RETAINING CLIP FROM THE CLUTCH AND PULL THE OLD CLUTCH OUT OF THE SHAFT.
7.THE CLUTCH KIT I ORDERED CAME WITH A PLASTIC BRAKE TO CLUTCH CAM SO I REPLACED IT TOO, JUST REMOVE THE RETAINIG CLIP FROM THE BRAKE THAT IS AT THE BOTTOM OF THE TUB AND REPLACED THE PART.
8.INSTALLED THE NEW CLUTCH AND THE RETAINING CLIPS IN REVERSE ORDER. REPLACE ALL PARTS THAT CAME WITH THE KIT. THE NEW CLUTCH SPRING WAS ALREADY IN PLACE.
9.PUT THE ASSEMBLY BACK INTO THE TUB AND RE-INSTALL ALL THE OTHER ITEMS IN THE SAME ORDER. IT SPINS GOOD NOW!
10.WHILE REPLACING PARTS, METHODICALLY CLEAN ALL THE LINT FROM THE MOTOR AND FROM UNDER THE MACHINE. THE GEARBOX SHOWED SIGNS OF LEAKING OIL SO ITS A QUESTION OF COST. I LEFT IT THERE UNTIL IT FAILS THEN I'LL BUY A NEW MACHINE.
All Instructions for the 11016512691
76-90 of 1,341