Models > 11016502694 > Instructions

11016502694 Kenmore Washer - Instructions

All installation instructions for 11016502694 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016502694
1,081-1,095 of 1,135
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer did not work after replacing agitatior parts

  • Customer: kimberly from Grass Valley CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I was thrilled that the agitator parts were so easy to replace, but that didn't totally fix my problem. I looked underneath the washer and found black rubber shavings from a worn part and looked online and found that the problem was most likely the Direct Drive Motor Coupling. I watched the video and ordered the part. The coupling was actually broken. After replacing the part, the washer works great...better than it has in years. I think I will work on our dryer now.

Lost the spin cycle and had a rumbling noise.

  • Customer: Brent W from Amelia OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I performed the repair the same as outlined in the video, but I didn't need to tip the washer on the back side. Once I removed the sheetmetal, I was able to swap out the drive coupler, and the new part is a better design than the one that broke.

Drum wasn't spinning during spin cycle.

  • Customer: Douglas from Blue Point NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the directions in the two videos that were provided on your web sight. It fixed the problem and it only cost us about $60.00. We were so thrilled with the results. We were almost ready to go buy a new washer. My wife suggested that we look it up on line and see if we couldn't fix it ourselves before spending the money on a new washer. Was she ever right! Thanks for providing such fine instructional videos.

machine would not spin

  • Customer: herbert from Canyon Country CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Following the video posted with the part made this repair a piece of cake, well documented, filmed, great explanations of tools needed and how to do it all. This is a fantastic site for do it yourself people with a little bit of mechanical skills. BTW I've been a hvy. eqt. mech. for over 40 years so this is something different to tangle with and a lot cleaner. Thanks so much for your time and consideration in produceing this instructional video, and keep up the excellent work.

washer would spin intermittently

  • Customer: Kristine from Los Angeles CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Parts Select is AMAZING!! It directed us to the correct parts. Ordering was easy. But the best part was the videos. The step by step instruction was a godsend. We followed it, paused it, compared it, did it. We had to battle grease and tight quarters, but got it done. The machine works good. We spent about $65 as opposed to $400+ for a new washer. Great website.

Washer stopped agitating and would not spin water out

  • Customer: Deborah from Brunswick OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
When my 13 yr old washer stopped working the timing was not at all good to spend money on a new one. I have two of my children getting marriied within the next year and funds are tight. I decided to troubleshoot it myself online by googling my problem. I found out what I thought would be the parts I needed, I took a chance and ordered them. The bonus was the videos that you emailed me with the complete installation instructions. I am a banker and a 53 yr old woman ...not exactly a handy man. With your videos I was able to fix my washer by my self for just the cost of parts...so my wedding budget is still in place. I highly reccommend PartSelect for anyone...cause If I can do it anyone can do it! Thank you PartSelect

Washer stopped spinning

  • Customer: Jeff from Michigan City IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
2nd time partselact has saved my ~13 year old washer for a total of ~40$ Entered the symptom and they told me more than likely what to look for and VIOLA ! Would've been easy to spend $200 each time my washer quit working but with a suggestion from a menu and even a video to show me how I revived my old $400 AMERICAN made washer to wash another day. Thank you part select !!

WOULD NOT SPIN

  • Customer: Robert J from Tidioute PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I WATCHED A U-TUBE VIDEO FROM A REPAIR MAN BY THE NAME OF ANGEL // THIS MAN IS A DETACATED MECHANIC KNOWS HIS JOB //USED HIS DIAGNOSTICS AND THE JOB WAS A PIECE OF CAKE // HE COVERS EVERY ASPECT OF ALL PROBLEMS //// PRAISE TO ANGEL ////

washer was making an awful noise

  • Customer: Jody from Indianapolis IN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video that was attached to the link where i ordered my part. Seriously, could not have been easier!! Thank you so much!!

Intermittently the spin cycle would not empty the tub fully

  • Customer: Robert from York PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off, let me say two things, this was my very first washer repair and the installation video was excellent.

Few things though ..... The first thing I noticed was the old parts I removed did not look that bad to me. I was starting to wonder if I was wasting my time. However, its apart now I'll continue on. I had a hard time properly seating the new couplings on either end correctly. They were VERY snug. What I ended up doing was getting a 20mm deep socket that fit perfectly onto the coupling and with a hammer gently, (and I underline gently) tapped the new parts into place. That fixed that problem. I also had some minor difficulty putting the cabinet back together, but nothing earth shattering. The cabinet fits on top of the frame, not under. And lastly, the small clips that hold the console on were not very reusable afterwards so I'll need to order a new set of them sometime.

All-in-all it was a fun repair that didn't take me too long and I saved quite a bit. I definitely would do it again if necessary. I've done about 5 loads of laundry since and everything seems to be working great so far.

- Bob

Motor Drive Coupling

  • Customer: Kenneth from Stoughton WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and that was a great help. I just entered my model number and selected the symptom. 61% of the time the drive coupling is the problem and it was. Ordered the part and got it the next day.

Washer full of water not draining

  • Customer: James from Port St Lucie FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.

The tub would not spin during the spin cycle. I diagnosed that the door switch was functioning. And through some reading on the internet, found out it was the motor coupling. I replaced the clutch assembly strictly as preventative maintenance.

  • Customer: Jorma from Saint Cloud MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

The washing machine started making a clicking type noise and would not drain after the rinse cycle completed.

  • Customer: Larry from Buffalo TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After entering the Parts Select website and searching for the model number information, I found a video which described the problem. The video explained the step by step procedure to access the possible problem. The problem was exactly as the video described, I ordered the repair part, made the repair, and placed the washer back in service. Oh, by the way, the part was delivered to my house the next day.

The washer was making noise and was leaving the cloth dripping wet at end.

  • Customer: Kenia from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Before I even watch any partselect videos to do the repair, which I should of from the very beginning, ah, ja, ja, I had already disassembled the back panel "my way" to the washer and trouble shooting the washer with my wife's help. While she tilted the washer backwards, I looked under and we found that the noise was coming from in between top of the motor where the direct drive motor coupling is located and the clutch assembly came together which I learned along with names and functions after watching the partselect installation video. Nice! Once I received the part it took me like 45 minutes to put all back together. Took loose two screws to clips holding the motor, pulled motor of mounting bracket finding the broken piece, replaced it, recouped reinstalling motor onto the motor bracket, clip, clip the two little screws and walla, got the wife her washer back, at bed time rewards, peace of mind the rest was history... Thanks PartSelect for awesome videos and great customer service!
All Instructions for the 11016502694
1,081-1,095 of 1,135