11016102502 Kenmore Washer - Instructions

I took the cover off the washer off, loosened all hoses and clamps remove old water pump and installed new one.

Follow the video for replacing the part if you're not handy. I watched part of it because I haven't played with (repaired) a washer in a long time. Mark the wire connections before removing them from the valve not critical but helpful. I actually needed the video for replacing the clips.

This was a pretty easy repair that only cost about $30 and 20 minutes to do. The video was very useful even though the Inlet was slightly different than the original. Putting the housing back on was the toughest part. The one thing they failed to mention is that you may have to unhook the outlet on the washing machine depending on how much room you have to work. I've never worked on a washing machine before so I was very happy with the ease it took to replace this part and that the diagnosis was correct. I bet this would have cost over $125 to have a repairman do it. I also found it easier to do with two people. We simply unhooked the hoses...remember which is which. It might be a good time to check and replace the hoses too. My cold water hose is in bad shape so I know now to replace it soon. After unhooking the hoses and the outlet...and unplugging it, we moved it to an open area to work on. Simply unscrew the control panel and flip it back, then uncl the wires to the lower part of the machine. Unclip the hinges and pull the body off. Then unscrew the old inlet, unclip the hose and the circuits...again remember which goes where but they are color coded. Toss the old one and replace with the new one and reverse everything you just did.

took off front cabinet removed pump,and then motor and replaced part.

Unplugged washing machine and tilted washer back toward wall. Loosened clamps,removed hoses from water pump and drained water into shallow basin. Pried retaining clips up with screwdriver and lifted pump off of motor shaft. Installed new pump on motor shaft and secured pump with retaining clips. Re-attached hoses and secured clamps. Returned washer to upright position, plugged washer in and ran it through a test cycle with no problems. Watched the video on the replacement of the water pump, so the process was very simple.

Washer started leaking so I carried it out on the back deck so I could still use it until I had time to fix it, ordered pump, it came in about two days, took about ten minuets to fix and put back in the laundry room. I've had this washer and dryer set for nearly twenty years, I do most things myself, ordering online and having the parts waiting on me when I get home makes things so much easier

Followed partsselect video repair guide... it went super.

Shut off water and unhooked lines. Pulled machine out,turned on back to access pump/hoses, noticed crack in pump. Ordered new part which arrived in two business days.Replaced pump which took 10 minutes,hooked washer back up and ran a test load of towels. Perfect.

Pretty much as directed. My only issue was the rust on the old part. It made it difficult to remove the old and to put on the new one. At first the new one wouldn't fit since the rust had essentially changed the size of the metal rod the new pump had to fit on. So I had to spend time sanding down/off the rust. But in the end I was able to do it and the part works great!

Watched the video and it was very straight forward, very easy and time saving. I just wish the delivery time for the part was that fast (It was a quick delivery).

Disconnected water and power supply. Turned washer face up and removed pump. Easy to install just 2 hold down clips.

Removed washer cabinet. Unclipped pump and disconnected hoses. Put hoses on new pump. Attached pump to drive unit and reinstalled cabinet.

It was a no-brainer repair. We removed the worn hose and replaced it with the new one. Only variable was that the new clamp was too big for our fitting, so we used the old one. The clamp was the only mechanical thing we did. The best part was the very prompt delivery of the new part and the help finding it from the rep at the company.

your instructions in the video were excellent, but the shaft of the motor was too corroded to reuse.

it went very fast after watching the how to fix video