Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11015732400 > Instructions

11015732400 Kenmore Washer - Instructions

All installation instructions for 11015732400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11015732400
1,111-1,125 of 1,162
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer vibrated during the spin cycle

  • Customer: David from Roswell, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.

Out of balance, could't operate

  • Customer: Arlyn from Driggs, ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The prooblem started with the hole in the bottom frame, for tub spring wore through, spring fell off, then a spring retainer worn broke in 2 releasing 1 suspention spring. All springs were about to fail, metal very thin at at the contact points. Drilled a new hole for the new suspension spring, replace all 3 brackets, worn also, springs, and retainers with a small dab of grease at the contact points. The new springs mad the tub more stable than before the failure, and silent when spinning or washing. Be careful to get the springs in the right direction, then the spring comes over the outside the brackets and retainers, other way they rub in spots. On this machine one was backwards from the factory 18 years ago, surely that accounts for more stable running.

when it would spin it would sheakall over .

  • Customer: Johnny from Las Cruces, NM
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just did it how the way it showed on the video it was easy

After 18 years and a family of four, my drain hose developed about a 3/4 inch split.

  • Customer: Robert from Carmichaels, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the body housing for the washer to find the problem, I left the housing off until my drain hose arrived (in 2 business days). Remember to keep your spring hose rings from the old drain hose. Within 10 minutes, I had the new drain hose attached and clipped in to the rear of the machine. Within 30 minutes, my wife was washing a load of clothes. **Reminder: This is a good time to thoroughly clean the areas of your washer that you normally do not get to. Also remember that your first load of clothes washed after the repairs and cleaning should be dark (i.e. jeans or work clothes) should their be any residual dirt in your drum after cleaning.

Water leaking from under front of machine

  • Customer: Kevin from Avondale, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the video and reading some of the instructions posted on Parts Select I disconnected the power cord, shut off and disconnected the water lines before laying the washer down on its "back" with help of a dolly.(IF you don’t own a dolly this can still be done without one but I recommend having a friend help you depending on your age and health) Once I had the washer laid down it became apparent to me that I didn’t need to take the whole "cover" off but could do the repair from the bottom of the machine. Following the instructions I first removed the hose clamps from the hose running from the pump to the tub and the hose that runs to the back of the machine where the drain to the wall attaches. I then "popped" the two clips off the pump as described in the video and after removing the pump I turned the clips to the side and removed them as well. At this point I removed the clamp from the "pump to tub" hose on the tub side and then removed the hose. I followed this up by removing the entire hose assembly that the "pump to drain hose" hose attaches too. Once you've seen this "assembly" you'll understand what I mean. Anyway, once that was done and the new parts had arrived (parts came quickly I placed my order on Thru evening and received them on Tues with the Labor Day weekend in-between) Install was as simply as removal, I laid the machine down using the dolly and then simply installed everything starting with "pump to drain hose assembly" then the "tub to pump hose" then the pump itself and finally both hoses to the pump. The "pump to tub" hose came with two new clamps however they are the type of hose clamps requiring the use of a screw drive to tighten not the original type it had on it that you just squeeze with pliers. I used the new ones that came in the package. The other hose didn’t come with a clamp and only has one where it connects to the pump, so I reused the original. I would suggest that you also check or just replace the drain line that runs from the machine to the wall at the same time as the rest of this repair as I did not and the 1st time I ran the machine that hose sprung a leak.

Washing machine leaking water out from bottom

  • Customer: David from Friedens, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected power cord. disconnected water lines, pulled outer drain hose out of home drain standpipe. tilted unit forward. removed outer drain hose. removed mounting screw for drain pipe with nut driver. removed inner drain hose (defective part) with pliers. installrd new part in reverse order. new part fit like a glove.

Hose cracked and leaked water all over basement floor

  • Customer: Edward from High Ridge, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Leaned the washer forward, removed the old hose and clamped on the new one. It took all of 5 minutes. The part was delivered in two days. I couldn't be happier with our experience.

Drum moves and strange noise when spinning

  • Customer: Kenneth from Hillsborough, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
When I pulled the machine out, I noticed one of the suspension springs on the floor. I followed the video supplied by PartSelect.com and suggestions by other folks. I started with the spring that was missing, which was a mistake since I did not know that there are custom spring clips which hold the spring to the drum. Once I found the missing part the installation was very easy. I used the suggestion by another post, of wedging a block of wood between the back of the machine and drum, to relax the rear suspension spring, which eliminated having to remove the back of the machine or tipping the machine on the back to get at the screw. I will always look to PartSelect.com for any future appliance repairs. You are the greatest

direct drive water pump

  • Customer: leon from hialeah, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
very well the part was easy to install and the part was easy to find on the diagram furnished by parts select

washer leaking even after washer was turned off

  • Customer: Vicky from Sairdealin, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
my husband looked at it and seen that the pump was leaking so we got on the internet and found Partselect found our part ordered it got it in 3 days my husband didn't have to take the base off he just reached in and took of the brackets off the old pump and put on the new .took about 15 minutes. thanks you very much for helping us we did watch the vedio which was good but he wanted to try it his way (you know men). and i'm glad to say it worked.

Water left in basket at end of wash cycle-not draining

  • Customer: Paul from Oakdale, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Since I live in a condo (upstairs unit) flipping the machine was not an easy option. So I was faced with having to get the remaining 2-3 gallons of water out of the drum. I rigged something up and collected 80% of the water, but be prepared for a mess. I was and it wasn't a big deal, just took more time. Once part was removed, I got online to find the part- which ranged in price from $67 at a local appliance part distributor to $49 from SearsDirect including postage. Parts select came in at $37 with freight and the part swapped out perfectly- just 2 clips that hold the pump on and 2 hose clamps (I used slip-joint pliers which works well). I checked YouTube for a video first and lo and behold, there was a video about a whirlpool water pump replacement, which helped some. Job went well and I didn't have to replace a $1200 all-in-one.

Washer Leaking

  • Customer: Kathy from Springfield, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
This is a not for men only job. The worst part was taking the flimsy, rusty-on-the-inside case on and off. If you've never done it before, I would recommend photographing each section that you take apart so you can more easily see how it goes back together. The video is a great help for general ideas, but unless your model is exactly like that one there may be other parts. Wiggling the clamps off the hoses wasn't easy as the wrench kept slipping of the clamp ends. Finally I figured out that a wrench that clamps on and stays put was the right answer. Replacing the pump was easy--just like in the video. Now I have a secondary problem: the water now gushes out of the standpipe when the water exits the tub. I think the pump is better than the last one even before it broke, so the water is coming out too fast. I found a little part that makes the exit hole on the drain hose a lot smaller, plus I covered it with a stocking in case the part came flying off. Last time I tested it only about a cup of water came out of the pipe. I think there may be air in the pipe, so I have some things to try for that but at least I feel like I'm going in the right direction. This site is great--I already paid for one professional repair and the washer isn't worth another one but I'd like to keep it running for a few more months anyway.

Water leaking from under the middle of the front panel.

  • Customer: richard from new holland, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on the Partselect website. Appled the same technique for my machine and the repair was just as easy. Unplugged the washer, removed two screws from the top panel, flipped it up and removed the two brackets that hold the cabinet in place. Removed the cabinet, the pump is right in front held on by two clamps. Removed the clamps, unhooked the hoses, put the new pump in attached the hoses and the clamps. I then put the cabinet back together and the repair was complete, wash machine is running again with no leaks.

Had water leaking from pumpon floor

  • Customer: Edward from Mecosta, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on the website on how to repair this and followed it. The repair went quickly. I spent more time moving the washer in and out of the location it was in than the time it took to repair.

Water pump had a leak near the central motion core

  • Customer: Catherine from Prescott, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Remove the outer washing machine housing. Close-up inspection located the leak source. The water pump was removed by popping off the upper and lower metal brackets, then removing it from the two rubber hoses with their pinch clamps. Ordering a new part was easy on your web site, and it arrived in 2 days! I reversed the process, with the smaller hose's pinch clamp hard to manage with simple pliers, but doable with persistence. I LOVE my 23 yr old whirlpool washer, and don't want a newer model, so thanks for making repairs doable for an old lady!
All Instructions for the 11015732400
1,111-1,125 of 1,162