Models > 1100PRW-K > Instructions

1100PRW-K Magic Chef Range - Instructions

All installation instructions for 1100PRW-K parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 1100PRW-K
16-30 of 170
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven would not turn on flame

  • Customer: Michael from Secaucus NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

no temp control

  • Customer: Cathreen from Lusby MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 44 people found this instruction helpful
very easy

oven wouldn't light

  • Customer: peter from marine city MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

Igniter glowed but oven would not light

  • Customer: Richard from West Mifflin PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...

igniter burned out

  • Customer: David from Milton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 2 of 2 people found this instruction helpful
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.

OVEN WAS NOT GETTING HOT

  • Customer: Joe from Duarte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
FIRST I WANT THANK YOU FOR BEING THERE
FOR ME .IF IT WASN'T FOR YOU I WOULD BE HAVING THANKSGIVING AT MY MOTHER INLAW

FIRST IREMOVED THE TWO SCREWSTHAT HOLDS THY ELEMENT IN PLACE. I THEN PULLEDTHE ELEMENT OUT ABOUT 3 IN AND
DISCONNECTED THE TWO WIRES .IT'S EASY AS
1. 2. 3

Oven wouldn't heat

  • Customer: Tom from Greenville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 2 of 2 people found this instruction helpful
I researched the stories on Partsselect, and it looked like this would be a simple repair. Fortunately, it was more simple than I'd thought. We bought the house (and stove) used, and the ignitor apparently had been replaced before, because the part was an EXACT replacement for the old one. I simply unscrewed the two screws holding the old ignitor onto the bracket/burner, pulled the wiring from the back of the oven through the insulation, disconnected the snap connector, reattached the new one. Then I pushed the wiring back through the insulation and added some additional insulation (provided with the part), making sure all extra length was pushed into the insulation. Reattached with two screws using a nut driver, replaced the bottom pan in the oven, slid the door back on its two hinges and started it up. Works perfectly. Thanks Partselect. You guys are great and I had the replacement my mail in about 5 working days!

Oven wouldn't heat.

  • Customer: Thomas from La Crescenta CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pushed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.

The oven igniter lit up but the valve wouldn't release the gas to ignite.

  • Customer: John from Wisconsin Rapids WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 2 of 2 people found this instruction helpful
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

oven would take a very long time to warm

  • Customer: Barry from East Islip NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like new .

oven wouldn't heat

  • Customer: Dana from Windchester IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
removed 2 screws and unpluged ingiter plug ed new igniter in replaced screws and worked fine

Oven burner would periodically go out and re-light

  • Customer: Richard from Merrimac MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 2 of 3 people found this instruction helpful
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.

igniter glowed but oven would not light

  • Customer: edward from euclid OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!

Oven would not start, ignitor was not doing anything

  • Customer: Michael from Syracuse NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 1 of 1 people found this instruction helpful
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up and then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.

broke the igniter in the oven before I even got the oven installed

  • Customer: june from wills point TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
All Instructions for the 1100PRW-K
16-30 of 170