Models > 10659422801 > Instructions

10659422801 Kenmore Refrigerator - Instructions

All installation instructions for 10659422801 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10659422801
871-885 of 993
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Not making ice

  • Customer: Klaus from Valencia CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Ordered part#PS2341899, received in 2 days. Unplugged refrigerator and removed ice cube drawer. Then removed shelf above icemaker. Used 1/4 nutdriver to remove 3 screws holding the icemaker in place. Then unplugged electrical harness from icemaker. To install, just do the reverse and job could be completed within 10 to 15 minutes. It is not necessary to turn water off in back of refrigerator. You should have ice cubes within a couple of hours, however it takes about 24 hours to fill the ice drawer. Probably saved over $150 by doing it myself.

icemaker stop working

  • Customer: Neure from Bronx NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It was simple, three screws two at the top and one at the bottom. Then unplug the wires that ran from the fridge to the icemaker. Reverse the pocedure to put in the new icemaker and take a jumper wire and start the cycle, finish. It was a simple exchange. The icemaker was a little expensive, but it works. Thanks partselect.

original ice make quit working. Was leaking

  • Customer: Dennis from Auburndale WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unit has 3 screws holding it in. The bottom screw must be taken out, but the two screws on the top can just be loosened. The ice maker then can be lifted upward and it will come out. The ice maker has slots that slide over the two screws. Once removed, the electrical connection can be unplugged. The new ice maker comes with electrical wiring,but needs to be removed. Just plug the wiring from the refrigerator in the new icemaker. The unit can then be put back in,sliding the unit over the top two screws and tightening them. Replace bottom screw & you are done. My unit did not start right away,but give it time. Within 2-3 hours it was working and making ice.

Teflon wore off the bottom of first few cube molds

  • Customer: Dave from Chaska MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Really simple repair. Turned off water to fridge, removed 3 screws with nutdriver, slapped the replacement part in and plugged in wiring harness and walla! Fresh ice without a giant glob of ice sitting in the tray. Parts were perfect match and had no issues at all!

Quit making ice,and the fill hose froze up.

  • Customer: Ronald from Brunswick OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Easy as making toast.Super fast delivery,Less than 24 hrs.

Ice maker was leaking

  • Customer: Richard from Tucson AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Turn off power & water, using a nut driver removed lower screw, loosen the 2 top screws. Lifted unit up and out a little to remove power cable. Removed lever and installed on new unit. Hooked up power cable install it over the 2 top screws, install bottom screw and tighten all 3. Turn on power and water, lowered bar. It started making ice in about an hour. NO LEAKS. Did not have to adjust water level. Took me less than ten min to complete.

freezer stopped making ice

  • Customer: Robert from Shenandoah TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took 1/4" nutdriver and loosened the two screws on top then removed the one screw underneath. It came out except for the wiring harness attached. My icemaker came with a wiring harness, but I elected to unsnap and use the one in the freezer to keep from doing more work on connection. Replaced the bail and heard the first ice drop in a couple of hours, then more ice till it was full the next day.

Ice making stopped working

  • Customer: Kimberly from Harrisburg PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Easily installed the part on Tuesday night. Had ice by Wed morning.

would not make ice

  • Customer: Charles from Chappells SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
old icemaker, took out bottom screw, loosened top 2 screws (do not take out) lift and lay down, take off front cover, a little clip will let you disconnect power cord. take old icemaker out of fridge. take off the wire to lift to cut off ice and put on new icemaker. plug power into new icemaker and hang on top screws. wait about 45 mins. and the new icemaker will make a cycle with no water or ice. at this point the new icemaker will fill with water and damn in about an hour or hour and a half you have ice. Oh, don't forget to put the ice bucket back in freezer. now tighten top screws. haven't put bottom screw back in yet.

Ice Maker stopped working. Only 4 months old - installed by Sears

  • Customer: Theodore from Garden Grove CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Messed with trying to get cable assembly plugged in for most of an hour. Finally swapped cable assembly with the old one. Plugged right in. Finished in 20 minutes.

Stopped making ice.

  • Customer: Allen from Oakwood Village OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the ice maker, researched the part number and ordered the part. I followed the instructions and Iinstalled the part.

The ice maker quit making ice.

  • Customer: Joby from Pasadena TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The installation could not have been any easier. First you will want to turn off the water supply and unplug the refrigerator. Next remove any shelves that are in the way of removing the old unit. Then you will remove the single 1/4" screw at the bottom of the unit completely and then loosen the 2 at the top (leave them in place as the ice maker sets down onto them). Next lift old ice make up and unplug the wiring from it. Finally reverse the process. It is worth mentioning that was forced to reuse the existing wiring harness as the old one was hard wired to the refrigerator. This presented no problem as the new ice maker is making ice .

my ice maker had stopped producing ice.

  • Customer: Carol from Eatonton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I received my new ice maker and got a nut driver and went to the freezer and removed my old ice maker . Then I noticed a problem. The cord on my old ice maker did not have a plug in the middle, my wires seemed to go through the wall of the freezer. I was afraid I would damage it if I tried to pull the wires from the wall, so I called customer service . She said I apparently ordered the wrong part. I had order a $70 unit and she said I needed the $114 kit. I would have to return the unit and order the kit. But she told me to look at the kit description and watch the repair video to see if that would help to see if I thought I could do it myself or get a service person. After looking at the parts and video I realized that the kit would be sending me the exact same unit and a couple of different type wire cords. I decided that all I needed to do was use the wire harness from my freezer and remove the new wire harness from the new ice maker unit. Of course I cut off the power to the refrigerator before pulling the plugs.I just had to loosen the two upper screws and remove the bottom screws, pull out the old unit, unplug the wire harness from the ice maker and removed the new wire harness from the new unit. Then I plugged the old wire into the new unit, slipped the unit back into position being certain that the water tube was in the proper position, tightened the upper screws, replaced the lower screw. I turned the power back on and waited. In a while I had ice again.

Ice maker was driping water out of the bottom front

  • Customer: Ronnie from Heidenheimer TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remover bottom nut screw and loosen the top two nut screws about half way out. Lifted up and foreward and then tilt ice maker to the right pushed in tab on electric plug and pulled plug out. Removed ice shut off rod and installed it on new ice maker. Removed nut screw on chute and removed chute. Installed new chute, plugged ice maker in and re- installed ice maker. Very easy and pleased with how quick I received the part after I ordered it.

Ice maker would not make ice. short fill & plastic gear slipping and locking up.

  • Customer: warren from hammond IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
trip breaker. remove and save cover. loosen 2 top screws & remove bottom support bracket. unit slides up and out. unplug wire harness . attach new unit to wire harness. slip new unit in clearing fill spout. attach bottom support bracket and tighten top screws. replace cover and set breaker. CREATE REAL ICE!!
All Instructions for the 10659422801
871-885 of 993