Models > 10656662500 > Instructions

10656662500 Kenmore Refrigerator - Instructions

All installation instructions for 10656662500 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10656662500
1366-1376 of 1376
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken icemaker during summer in Texas.

  • Customer: Colin from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The online video shortened the learning curve, and the cut the repair time in half.

would not make ice

  • Customer: Cynthia from Hinton VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video then made the repair it was just like the video said very easy

Ice maker stopped working

  • Customer: Elmo from Palm Coast FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
April 2012
My ice maker (2001 Whirlpool Gold side by side) stopped making ice. Using the model number (inside fridge, right wall), Google found the partselect website containing diagrams of the entire refrigerator. Using the "freezer liner" and "ice maker" diagrams, I discovered that electronic control boards, control and motor assembly, and water inlet valves could cause the ice maker to stop making ice. Since the LED lamps in the freezer liner were not working (diagnosis described as part of the emitter control board description), I replaced the emitter control boards first. After installation, the lights worked properly, according to the diagnosis, but still no ice. It seemed logical to next replace the control and motor assembly. About two hours after installation, the ice maker produced cubes, and has been working since. Each of the two parts orders from PartSupply came within 3 days, and were the correct parts for my machine. Installation illustrations were accurate and helpful

Ice maker not working

  • Customer: Gary from Plymouth MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the part recommended by your site, followed the instructions of the associated video and new ice is piling up right now. My only concern was no action for a time right after the install. Turns out the temperature of the freezer must drop back down to ?? before the ice maker starts to work. I was thinking maybe the electrical connection was not good. I choose to wait a night and see if change would occur. Freezer cooled down and ice maker started.

Gary

stopped producing ice

  • Customer: Walter from Palm Beach Gardens FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as shown in the video; had a bit of trouble with the wiring harness, but all else went smoothly. If it were not for the explicit video installation instruction, it could not have been done by a do-it-yourself guy with tools. I had ice again in 3 hours! PartSelect is the absolute best when it comes to diagnosing, ordering and installing the part(s).

No water coming into ice maker

  • Customer: Ricardo from Hialeah Gardens FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.

Unit stopped making Ice

  • Customer: Denis from Columbia IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found my unit had stopped making ice. I did 20 min. of search on the internet and found this site. I was going to just buy the whole ice maker unit, but after reading a bit more found that the majority was just the motor assembly. I ordered it, 2 days later it was at my front door. I pulled the ice maker unit out, took off the motor assembly, and low and behold a small whit ppiece of plastic fell out. I replaced the motor assembly re installed the ice maker and in one hour I had ice again. As far as ease to do this job from 1 being hard and 10 being super easy, I would rate this a 10+. If you have this kind of problem, I would not waste your money on a repair man, 150.00 service call, Hell no. 65 bucks and your done. Before your wife can make you a pot of coffee this can be out and back in. I don't want to take money away from the appliance repair men but some repairs can be a DIY project. Nut driver and phillips screw driver is all you need.Hope this helps ya.

timer motor died

  • Customer: Paul from Moline IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas

ice maker wasn't

  • Customer: Mona from The Sea Ranch CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

Needed extra shelf on refrigerator door

  • Customer: Virginia from Naperville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We wanted an additonal shelf on the door of our 10 year old refrigerator. I called because I wasn't sure what to order. The saleswoman was very helpful and friendly and my order was placed quickly. It arrived in just a few days and was easy to place on the door. It is now in my refrig holding lots of little jars and bottles. Thanks PartSelect! We wonder why it took us so long to think to order this!

Cracked drip tray

  • Customer: Michael from Ft. Myers FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.
All Instructions for the 10656662500
1366-1376 of 1376