Models > 10656542400 > Instructions

10656542400 Kenmore Refrigerator - Instructions

All installation instructions for 10656542400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10656542400
1,201-1,215 of 1,273
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker stopped working

  • Customer: Steve from weatherford TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
No prior experience in appliance repair. The majority of time was used in researching the problem and how to fix it. The Parts-Select website and the comments of prior customers made it easy to diagnose and repair. Unplugged the unit, popped of the ice maker cover to get it out of the way, unscrewed the plate covers for the emitter and receiver, changed them out, replaced the covers, replaced ice maker cover, plugged in. Moved on to the next problem.

ice maker went gaflooey

  • Customer: peter from summit NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
figured it was either the emitter/receiver or the control module.. even tho the online stats said it was probably the control module, i had a gut feeling (along with a volt/ohmeter) that said it was the emitter..... ordered the part.. came in 2 days..... six screws..... BOOM DONE !!fresh ice !!!!!ohhh what afeeling !!! pete s.

Icemaker would not stop making ice.

  • Customer: Barry from Henderson NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Purchased the recommended/required electronic control boards for the sender and receiver. Removed the units and replaced the boards and reinstalled. Icemaker is working fine since the repair.

stopped dumping ice. The ice was frozen in the tray but not emptying into door bucket

  • Customer: David from Schnecksville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the 3 screws from the receiver first, on hinge side with the flap The toughest part was twisting my arm around and upside down to plug the new board into the wire harness since it had very little slack and the wires were stiff from cold, the emitter on the opposite side was as easy, care needed to be taken with the upper screw partially hidden behind ice maker itself but it was an easy removal. Again, short wires and stiff from cold make alignment of the plug to the board just bit awkward to ensure it was seated properly. 15 mins later I heard the first emptying of the ice maker

No ice

  • Customer: Robert from Boca Raton FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 3 screws on the emitter and 3 screws on the receiver. Removed the plugs and reinstalled the parts. Very simple and easy. Ice is flowing again.

ice maker stop making ice

  • Customer: Jim from Headland AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Did exactly what the video showed . First I went through the test procedure to conferm my boards were bad . But ice maker didn't work after the control boards were replaced. I did some more research to find out what the problem now could be. I discovered where the water goes into the ice tray the line was frozen. Got the hair dryer out and melted the ice that had the water restricted. Been making ice every since. I tell everybody about (part select) web. Sight now

no ice

  • Customer: Nancy from Midlothian IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy

Ice maker stopped making ice.

  • Customer: Walter from Gibsonville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After determining by the flashing light code what the problem was, I ordered the parts. Once the parts arrived, it took 15 minutes to install them by the instructions that came with them and two hours later I was making ice again. Very easy repair and there is a video on the website that shows exactly how to do it.

Ice machine stopped making ice

  • Customer: Randy from Belleville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Open freezer door and close flap on the left being sure not to block the infrared beam. If red light goes solid in a few seconds the Emitter receive and xmit boards are good. Unplugged fridge, Took the ice machine out took off the motor/controller cover and jumpered the two test points together with a short length of insulated wire. place the ice maker back on bracket to free up my hands and plugge in the fridge, turned ice maker on. Closed the flap and ensured red light was on solid and I was not blocking the beam... the motor control wheel did not turn slowly/cycle as it should have with the jumper inserted... Motor/controller assembly was bad. Pulled out icemaker and noticed some corrosion in the ice tray so ordered the entire ice maker instead of just the motor/control assembly... cost only about $30 more. New ice maker arrived and I installed, took about 10 hours before it got cold enough and began making ice.

Ice maker would not make ice

  • Customer: Steven from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Installed two circuit boards which was very easy & within 30 minutes ice was being made

ice not making

  • Customer: dennis from West Monroe LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replace the emitter and receiver which is located on the left and right side of your freezer when you open the door. use a crosstip head screwdriver remove the 3 ea. screws on the emitter frame ,dothe same for the receiver. replace the electronic boards and reinstall.wait at least 30 minutes and listen for ice to drop in the ice bucket.

Ice maker quit making ice

  • Customer: david from Surprise AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the reviews on how to test if part was bad. It was! Ordered new infered sensors and watched your repair video! 2 hours later the ice maker was making ice:) Very easy! Thanks David

Ice maker would not make ice

  • Customer: celene from Lavonia GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Completely disconnected the power. Just shutting off the ice maker switch does not shut off the power to these boards. The emitter and Receiver boards are located in the side panels of the freezer-one on the right and the other on the left. Just remove the 3 screws in each cover and disconnect the wire connectors and install the new boards. It's very straight forward and easy to do.

Not getting ice

  • Customer: linda from lambertville NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Replaced the optic boards - no lights working. Still no ice. No water coming into ice machine. Followed instructions on your website and diagnosed frozen line. Took ice machine out, used hair dryer, reinstalled and we have ice! Thank you so much for saving us a repair bill!!!!! Buying the part from you was very easy and your videos were excellent!!!

Ice maker stopped producing ice.

  • Customer: Gregg from Mahtomedi MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaces transmitter circuit board. Removed (3) screws and replaced board and replaced back into service. very easy!
All Instructions for the 10656542400
1,201-1,215 of 1,273