Models > 10656536400 > Instructions

10656536400 Kenmore Refrigerator - Instructions

All installation instructions for 10656536400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10656536400
1,096-1,110 of 1,499
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice from ice maker

  • Customer: William from Moscow, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Parts Select has great videos that describe step-by-step how to perform the repair. I did a sloppy job of diagnosing the problem, and concluded it was the water valve. The actual problems was that the ice maker was not sending a signal to the valve to send water. I could have determined this if I had tested the ice maker using all of the connection points where a jumper wire could be inserted. The ice maker arrived on my doorstep exactly when promised, and was an easy ten-minute fix. My conclusion is that an average person CAN work on their own appliances with a company like PartsSelect to backstop them.

Ice maker not making ice.

  • Customer: Tracey from Louisville, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed instructions posted on your site. It was straight forward and very simple to complete.

Ice maker sopped producing ice

  • Customer: Steven from ORLAND PARK, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Initial diagnosis incorrectly led me believe the problem was with the optic eye. After replacing the optic eve and still no ice, I realized the problem had to be with the actual ice maker itself. The removal of the old ice maker and installing of the new one took less than 5 minutes. This of course was after watching the repair video first. I still feel that I saved money by doing the repair myself instead calling in a appliance repair man, even with the added cost of the probable unneeded optic eye replacement. I am very satisfied.

Ice Maker quit working

  • Customer: Melanie from Murray, KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The ice maker quit working about 4 years after we purchased this refrigerator. I asked several contractors if they knew what the problem could be. All believed it had something to do with the water line being stopped up. However, when I looked at the water line, it seemed fine. Thankfully when I googled about repairing this refrig, I came upon this website. It stated statistically that the Icemaker assembly part was the problem. Guess what? Replaced it and it works! The repair was a little tedious, so I got my next door neighbor to help. He has a few moments struggling getting it out and the new one in, but overall, it was not too difficult. I believe I could have done it with the video's help but certainly would have taken me longer.

Ice maker quit working, then the fridge & freezer stopped cooling

  • Customer: Ina from Altamonte Springs, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I actually purchased an ice maker, a combination start device & a run capacitor. I watched the 2 videos which were very helpful, in fact I may not have been able to do this if I had not watched the videos first. It took me step by step. It couldn't have been more simple. I replaced the start device & the run capacitor first just to make sure my fridge would cool again, then when it did, I replaced the ice maker. I saved myself a service call ($59.95) and the labor to replace the ice maker & other parts($140)and that didn't include the parts! By the way I'm female and 71 years old. So if I can do this anyone can.

replaced ice maker

  • Customer: V.C. from Baytown, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
i followed instructions on video it went real simple except for the small area to work in.

Failed to make ice

  • Customer: Billy from Horseshoe Bay, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your repair video was spot on. Should have watched it before I removed the old defective part. Would recommend it for anyone with same problem. I'll call on you again. Thank you. Billy

Ice maker not working

  • Customer: Mercedes from Lyndhurst, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We replaced the ice maker with the help of the video, it was very helpful and it is working fine, thank you very much.

Ice maker stopped working

  • Customer: Kevin from Fort Lauderdale, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After viewing the very clear video. Remove the ice maker door by first lifting the door and pressing in on the hinges. Remove the screw in the back lower right of ice maker with a one quarter inch nut driver and lift out the cover to expose the wiring harness. Pull the ice maker unit forward and out and reach behind it to pull out the wiring harness plug. The plug only comes out if you depress the small "push clip" in the center of the harness plug. Turn the old ice maker unit upside down and remove the three screws again with the one quarter inch nut driver to lift off the plastic cover. The wiring harness plug need to be pushed through the plastic housing to remove the plastic cover completely. Reinstall the plastic cover on the new ice maker. Reverse the procedure and install the new ice maker. This is really a simple repair if you watch the video.

Water would come through the door, but would not make any ice

  • Customer: Chad from Marrero, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the (3) screws on the bottom of the ice maker & the (1) screw on the electrical cover plate. I unplugged the ice maker & completely removed it from the freezer. Make sure to pay attention to the locking tabs or your maker will not come out. I took the bottom plate off the old ice maker & attached it to the new one, slid it in & re-plugged it. Tighten all screws back where they are to go & now I have ice. It was a breeze to do this job. Part was completely as described.

The icemaker stopped working

  • Customer: Patrick from gilroy, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaker and installed the new one. Went from six tiny ice cubes to four big ice cubes. Ice is of a higher quality, and the ice no longer falls out of the bin as the old ice maker's ice had once been prone to doing. A certified epic win on my part.

Water leaking and freezing on the botton of the icemaker mold

  • Customer: Richard from Jacksonville, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Install was done in reverse order of uninstall. The only thing that made this install a bit tricky is that the fill cup on the replacement icemaker was not the same part as on the original. I could have attempted to trim the replacement fill cup but didn't know how well that would work. I instead elected to install the original fill cup onto the new icemaker. This added a bit of time and complexity to the repair but I followed a repair video for when just the ice mold is being replaced. That video told me how to disassemble the ice mold and timer motor which had to be done to in order to replace the fill cup. It's been about 2 weeks since repair was made and the icemaker seems to be working properly.

Broken Parts

  • Customer: NADIA from GARNER, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My humidity control and veggie drawers were cracked and broken, I had shopped around but the price to replace them was too high and not in my budget. I came up on partselect.com while searching to find a more reasonable price. The price, service, delivery and customer service was outstanding. One of the drawer had been damaged during shipping, I called them and they sent another one free of charge right away. I had a very positive experience and I have added them to my favorite web sites.

None

  • Customer: William from Harvest, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Order at 2:30 PM on Tuesday and had it by 1:30PM Wednesday. Less than a day on the delivery order. Thanks!

Crack on front of crisper pan

  • Customer: Kristine from Fort Worth, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I cracked the crisper pan after having the refrigerator only one week and needed a replacement ASAP!! I was so happy to find this site and the part I needed. It's a little pricy for a plastic drawer but I can overlook that since it was in stock and I received it the very next day!!!I took out the cracked pan, slid in the new one and I was done!!!! No more unsightly crack!
All Instructions for the 10656536400
1,096-1,110 of 1,499