Models > 10656536400 > Instructions

10656536400 Kenmore Refrigerator - Instructions

All installation instructions for 10656536400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10656536400
1,051-1,065 of 1,457
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Parts

  • Customer: NADIA from GARNER NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My humidity control and veggie drawers were cracked and broken, I had shopped around but the price to replace them was too high and not in my budget. I came up on partselect.com while searching to find a more reasonable price. The price, service, delivery and customer service was outstanding. One of the drawer had been damaged during shipping, I called them and they sent another one free of charge right away. I had a very positive experience and I have added them to my favorite web sites.

None

  • Customer: William from Harvest AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Order at 2:30 PM on Tuesday and had it by 1:30PM Wednesday. Less than a day on the delivery order. Thanks!

CRISPER DRAWER WAS BROKEN

  • Customer: Christopher from Parish FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
TOOK THE PART OUT OF THE PACKAGE AND INSTALLED IT. THE SERVICE I RECEIVED WAS EXCELENT. GOT THE PART TWO DAYS AFTER ORDERING IT

Broken Crisper Pan

  • Customer: Jodie from Riverview FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
No repair needed, just replacement but I would like to say that you did a fantastic job getting it to me. I ordered the part at approximately 2PM and by noon the next day, it was at my front door. Thank you for shipping so quickly.

Ice Maker quit working

  • Customer: David from Castalia OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

Broken drawer

  • Customer: Debbie from Westland MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced old drawer with new. Did have to remove white handle, the new one doesn't come with one. It was simply a matter of prying up the edge until it would come off and snapping it in place on the new one. Used the screw driver to lift pry up the edge.

ice maker stopped producing ice

  • Customer: Dennis from Lake Almanor CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
very simply followed installation instruction...removed 5 screws, disconneted electrical plug-in, installed new ice maker.

Replacing Icemaker in side-by-side refrigerator

  • Customer: Lawrence from Silver Spring MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
About a year ago, my icemaker stopped making ice. Knowing that a "house call" would cost a fortune, I delayed calling for a repair. Then I discovered the instructional videos on this (and other) websites. Looked like a relatively easy job. Troubleshooting the problem, however, had me scratching my head. Was it the control unit? the ice maker? the water pump? a frozen water line? A 4 day power outage allowed me to rule out the frozen line. The forum here allowed me to rule out the control unit (the blink codes indicated that it was working). So, the pump or the icemaker? Hmmm. I poured some water into the icemaker to see if it would make ice (I think that was a hint on the forum). No ice, so I ordered a new icemaker (and it arrived very quickly). It was very easy to take the old maker out. Some very minor complications with the new icemaker. First, the "funnel" for the water into the icemaker was a bit taller than the old one so had to manuever the water tube into the "funnel". The second problem is that the electrical connector on the icemaker seemed to be longer than the old one so the connector extended beyond the white cover. Not really a problem but it made it difficult to fix the cover over the wire. In the end, it just left it fitted loosely, without screwing it in place. All in all, however, a very straight forward undertaking (made even more so by the excellent videos)

Ice make did not make ice

  • Customer: Susan from Collegeville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the old ice maker. disassembled the part to reattach the housing to my new part. Hooked up the wiring and reinstalled the part. VERY EASY!!!!Our repair man had quoted me a price over $500. I was all done for under $150 including a new drip guard!

Icemaker stopped making ice.

  • Customer: Jim from Canyon Country CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My icemaker lasted about 3.5 years which appears to be longer than most. I first verified that the IR sensor blink codes were OK. Open the freezer and view the status led. Press the emitter flapper to unblock the optics beam. If the LED is on steady: The optics are working properly. If 2 BLINKS FOLLOWED BY 1 SEC. DELAY(Then repeated) The optics are faulty. Replace the emitter and receiver boards. In my case, I need to replace the icemaker. First watch the video. It will show you the hard to see screw and hidden plastic tabs to release the icemaker. Next remove power from the refrigerator. Remove the rear screw and use a flat blade screw driver for the tabs. The fill tube on on my icemaker was a bit longer than in the video so it caught on the icemaker. Carefully bend the rubber tube and the unit will slide out. The electrical connector has a release tab and may required a bit of effort to pull apart. Transfer the other parts per the video. Then reverse the procedure. This really is an easy repair and the video removes the guess work. The ordering process from PartSelect went smoothly and I received the part in 3 days. This is my second order from them and I am very satisfied.

no harvest

  • Customer: Gerald from CARY NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Assumed a broken ice maker motor, since I tried to force a harvest (jumped T-H) and it did not work, and it is 6 years old. Ice maker went in easy, harvested 3 or so times and quit. Forced another harvest (with the bucket on the door, you have to remove the ice maker to jump the points (PITA)wish they could make the jump points more accessible, like on the old units, mounted on the side). worked about 5 times and quit. Next step is the optics, which, as an old computer guy I find it hard to believe that a circuit board is bad intermittently. As an aside, the door jam gets hot, when I believe it is during harvest time. I vacuumed the coils, but it still heats up... only intermittently, coincidence???

ice maker

  • Customer: John from Huston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
video terrific...... could not tell on unit the type of electrical harness tab ..which showed on video and I changed quickly ....spent more time on extraneous ice.....sales rep was extremely helpful in picking the right unit...which I would not have been able to do from my model #....recived unit in two days.........

Would not dump ice

  • Customer: Lester from Metairie LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered a complete ice maker assembly from PartSelect. It came in within 3 days.I watched the video on the installation. It was very helpful.I removed the old ice maker and installed the new one within 15 minutes. A hour later it was working like new dumping ice. Anyone can do it. Its very easy. 100% satisfied.

ICE MAKER STOP WORKING

  • Customer: Michael from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
SAW VIDEO ON WHIRLPOOL WEBSITE

The ice maker was not making ice

  • Customer: Mark from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The ice maker was replaced easily with the help of the repair video. However, that did not fix the problem. With further investigation I found that the more common problem was the emitter boards. I replaced the new ice maker assembly with the old one and ordered the emitter boards. Partselect allow easy return of the new ice maker and I received the emitter boards and easily replaced them and ice is making as I type. Great experience and supper helpful repair videos.
All Instructions for the 10656536400
1,051-1,065 of 1,457