Models > 10656536400 > Instructions

10656536400 Kenmore Refrigerator - Instructions

All installation instructions for 10656536400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10656536400
1,036-1,050 of 1,457
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was constantly running and not getting hot

  • Customer: HENRY from WARMSPRINGS GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.

ice door frosted up

  • Customer: Deborah from Kimbolton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Once we figured how to get front off, it was like a puzzle. One piece at a time. So thankful part has been improved and replaced. It works better than before, just wish would have done it sooner.

The Ice Bin Coupling Crumbled Like A Cookie

  • Customer: Michael from White Plains MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After watching Steve from PartSelect.com, I was pretty confident. His video lasted only 2 1/2 minutes however; it had taken me only half the time. Since all blades were in tact, I held the top blade (inside the bin), unscrewed the bin coupling screw; added the coupling and washer and replaced the screw. Now I'm back to having cold beverages on call... Tks.

broken cap

  • Customer: John from Latham NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took off Old Cap Put Knew One On.

Both sides stopped getting cold

  • Customer: Lynda from Gary TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I'm a 65 year old widow on a limited SS income, so I needed to get my refrigerator fixed as cheaply as possible. Partselect's troubleshooting guides took me right to the problem. I ordered the part on a Friday and it arrived the next Tuesday. It probably took me a little longer than it would a repairman, but I did it myself with just a screwdriver and a nut driver and it only cost me $45 instead of the $200 plus it costs my daughter to have someone else replace hers two years ago. Always remember to unplug amy electrical device before removing the covers or attempting any repair. All I had to do was remove the lower back cover on the refrigerator and, using the partselect diagram, locate the casing that covered the start relay and the overload switch on the left side of the compressor. I popped the casing off with the screwdriver, pulled the relay off (it's sits on two prongs), and remove the red terminal wire from the relay. Installation of the new relay is the reverse steps of the removal. Thanks, Partselect! I will be doing business with you again if the need ever arises.

Noticed fridge was not working; compressor would turn on for 10 seconds then shut off

  • Customer: Sean from Savannah GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced broken fridge with a spare fridge; mean while I went online and did research and came across "Parts Select" which was extremely helpful with similiar situation and helpful guidance. $80 and fridge is as good as new.Thank you.

refrigerator runs great for 4or5 days then shts down youcan turn the thermostst down and back up or unplug it for a few seconds and it starts up again most of the time.

  • Customer: Darrell from Smithfield VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the relay started right up did fine for about 4 days. Came home from work I had lost everything in the freezer again.turned down the thermostat and back up and it started right up. 5 days later same thing again.

Refrigerator stopped working completely.

  • Customer: Lyudmila from Nampa ID
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just replaced the old Push-On Start Relay and it started to work again.

Heard Ticking every minute - Fridge/Freezer not Cold

  • Customer: Chris from Bellingham WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the start relay in about 5 minutes and plugged the fridge in and it started working. Easy repair to get fridge working again.

stopped chilling

  • Customer: Dave from Harrisville UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did a Google Search for a 1998 Whirlpool ED22RF, looked for trouble Isolation procedures. Don't remember the web sites but two parts were mentioned namely the timer and the thermal relay. After making sure it was unplugged I removed the back lower insulation panel, removed the red wire from the relay located on the left side of the condenser and unplugged the relay. I examined it for physical damage before checking with an ohmmeter and found the thermal relay sounded like it was full of sand when I shook it. So we found PartSelect and searched for the thermal relay and found an exact picture with the part number and ordered the part. We received the $30 part 5 days later. Only took 15 minutes and two tools to install. Thank you for saving us a few hundred dollars.

Ice door would not shut which lead to ice melting and freezing up Ice chute.

  • Customer: Doug from Arvada CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got Online to Parts Select put in the model number, selected from parts schematic, Ordered parts. Reviewed YouTube instructions supplied by Parts Select, Canadian service tech in video very knowledgeable about repair, followed his instruction and fixed the Ice maker. Very easy with Parts Select help.

Ice despenser stoped working, auger motor worked if door flap was opened fully manuallyw

  • Customer: Jolene from Merritt Island FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Googled the problem and after reading several posting & suggestions decided that the Ice dispenser kit would probably solve the problem. I ordered both parts on the chance that it might be only the micro switch and it was only a $10 part, the ice dispenser kit was $50. The access was really easy and the switch was installed in about 20 minutes but did not solve the problem so I proceeded with the kit. The parts came out fairly easy but our actual set up was slightly different from the video and print instructions. Our model did not have the heating ribbon on the door flap and the little barrel part was permanently attached to the refrigerator so I thought I could be in trouble. Did not realize that we had cracker the lever bracket clip during removal so my husband "brainstormed" a fix. That's what we needed the large head screw and drill for. We drilled the screw into the refrigerator so it holding the spring loaded piece tightly in position. Works fine. I was told my a repairman over the phone that the dispenser was probably not fixable on our model. I saved an expensive service call AND GOT THE DISPENSER WORKING!

Refrigerator Freezer Ice Door Broken

  • Customer: Peter from Wildomar CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Job went as per your terrific video. Except that when attempting to retrieve the old heater element the glue on the old door was no long pliable. I had to literally tear the old foam apart to get at the heater element and almost damaged it. Not to worry. It worked out well and all is great. Thanks for the very instructive video.

When you pressed on ice maker to get ice it was hard to get it to dispense

  • Customer: Dennis from Gig Harbor WA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed along with the Video from the web site. I used the masking tape to keep the electric parts out of the way. one of the attaching points for the new ice door broke off so i used J B Weld to reattach it. then the repair was finished with out a hitch. The time was extended by the need to wait for the epoxy to cure

Ice dispenser was broken

  • Customer: Helen from Escondido CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My handyman did the repair. It was pretty easy for him. It would have been a real puzzle if we had not watched the video instructions. The new parts were slightly different than the old parts, but they fit perfectly. I thawed the frost buildup around the ice door and the opening of the ice bin with a hair drier, to get the ice to come out properly. Thank you so much for the video!
All Instructions for the 10656536400
1,036-1,050 of 1,457