Models > 10654606300 > Instructions

10654606300 Kenmore Refrigerator - Instructions

All installation instructions for 10654606300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10654606300
1,126-1,140 of 1,196
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leak under refigerator

  • Customer: Ronald from Taylor TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My wife could have made the repair, I got on line, typed the problem in and PartSelect came up. The drawings were there as well as instructions. The part came, again with instructions and it took about 20 min. Good job guys.

ice maker not working

  • Customer: William from East Canton OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Shut off water & electric.Remove 2 screws,cut water lines,unplug electric plug. Install electric plug,push water lines in.reinstall screws,hook up water line & plug in ref.Turn water on, ck for leaks.

Water was dripping from the water dispenser at the front of the refrigerator.

  • Customer: Rick from Garland TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I pulled the refrigerator away from the wall, unplugged the electrical cord, and turned off the water going to the refrigerator. I then removed the cover on the bottom rear of the refrigerator by removing 7 or 8 small screws. Luckily the new and old valves were exactly the same except for some color coding. There were 2 screws to remove that attached the valve to the body of the fridge. There were 3 plastic tubes that connected to the valve and 2 wiring harnesses that plugged in. Before removing them, make sure to note which tubes and wires went where. The 3 tubes on the old valve were the push in type, just like the new one. I could not pull 2 of them out like the instructions said. I had to pry them out with a screw driver. In doing so I warped about 1 inch on the end of each tube which I then cut off with a razor blade. The electrical connections pulled out easily. I then pushed each tube back into the new valve which was very easy and pushed the electrical connections in. I attached the valve to the fridge with the 2 screws, turned the water on, plugged in the electrical cord, and checked for leaks. I put the back cover on and was back in business. It took me about 40 minutes but when I was younger could have done in in half the time.

Ice make isn't filling due to frozen/plugged water line

  • Customer: Matthew from Yucaipa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pull out the refridgerator from the wall. Unplug the fridge and turn off water supply. Remove the cardboard cover from the bottom of the back side of the fridge. The valve assembly is on the bottom right side of the the fridge when looking at the back. Remove the valve assembly. remove the color coded electrical connectors. Push in the quick disconnect fitting on the valves and gently pull the tubes out of each valve, if it won't come out you can cut the lines, just make sure they are nice and clean and straight. The new part was a perfect fit. Push the tubing in to the size matched valve inlets reconnect the electrical connections reattach valve assembly to the fridge, next open the freezer door and lift the ice make door and take you a hair dryer,turn it on and hold it about 1-2 inches away from the rubber hose that is used to fill the ice maker for about 2-3 minutes to remove the ice blockage. Once it is clear, turn on the water check for leaks and verify correct operation of water and ice. Reinstall the card board, push the fridge back into place. and enjoy a cool beverage and pat your self on the back cause you just fixed your ice maker!

My water dispenser quit on the door.

  • Customer: Jeff from GALLATIN TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I knew my ice maker was still working and I could hear that the switch on my water was still making the usual noise when tripped, so I knew that it had to be the inlet valve. I googled some videos and luckily found PartSelect.com. I used there diagnostics, looking at the percentages of other parts used to fix like problems. The part install was very easy as all I had to do was turn off the water and unplug the frig, remove the part, cut the input line and both output lines. Then slide those into the new part, with quick connects you just slide them in, the old part had compression fittings. Reattach the new part turn on the water, plug it back up, watch for leaks, your done..pretty sweet.

Cold water and ice maker not working.

  • Customer: Steven from Cary NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions in the package, after having viewed the video (from PartSelect, but you have to go to youtube for it.) Replacing the valve got the cold water flowing but there still is no water going to the ice maker.

Continuous water filling Ice maker

  • Customer: David from Las Vegas NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First Shut off Water supply from wall/valve. Turned off Ice maker switch interior freezer compartment. Removed power cord from wall plug, important for safety due to close proximity of cooling fan to valve, and resets electrical cycle to new valve to start water flow to ice maker once replaced. Removed lower back cardboard access to frig with nut driver, cleaned all (dust-bunnies)from coils, drip pan and all areas under frig with shop vac. Remove 2 screws (same size nut as cardboard back) to remove valve bracket from mount. This model frig had push release connectors so was even easier than expected, push collars up and pull out tubing, (residual water came out so have towel handy) had new valve positioned exactly how would reinstall so just pushed water line into new valve connector, then repeated process for all 3 water lines. Last unplugged electrical connectors and plugged into new valve in same position. Reattached new valve to mount w/2 screws, turned on water supply to check connections for leaks. (Finding none) Plugged electrical cord back into wall, used water pitcher to cycle water thru door water dispenser, waited for first cycle of water to fill ice maker. So easy and quick. Thank you to previous people who gave directions, and Partselect for easy diagrams, ordering, and shipping quickly.

Water overflowed icemaker

  • Customer: Stanley from Sharpsburg GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
My first try was to replace the water inlet valve. New valve was a good bit different than the original but not too hard to figure out. The main water inlet is on the inside rather than the outside. Flex hose and a stick in connector were included and I was able to work through that. But, when I turned it on the water still over flowed. The only thing left was the Ice maker. I ordered a new one. It came broken into several pieces. I ordered another, it arrived overnight with expediated shipping. install took maybe 15 minutes. problem solved. The company refunded me the full charge for the damaged ice maker and most of the charge for expediated shipping on the replacement. I'm happy and my wifes very happy.

No Ice then overflowed water at ice maker

  • Customer: Rickey from Newalla OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The problem with our ice maker started when it stopped making ice. It was a hit or miss problem. One day it would make a bin full then couple days later none. One morning I noticed that there was water overflowing from the ice maker which froze inside the freezer. I ordered the maker and valve after watching the videos on this site. With those videos I was able to fix the problem in no time. Ice maker has been working properly for over a week now. My wife was ready to get a new fridge but I was stubborn and wanted to see if I could fix it. Thank you to partselect.com for the fast shipping and great instructional vids.

No water in icemaker

  • Customer: EDWARD from GARDNERS PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
After figuring it out, Some changes had to be made, but everything went smoothly

Missing kick plate after a move.

  • Customer: William from Decatur GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Located part on your easy to use and understand site.Ordered one day and received the next (less than 24 hours). Easy to install. Very pleased with this seller...A+.

Refrigerator door not closing on its own

  • Customer: Kenneth A from Greeley CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove all items from door. Remove bolt holding plastic cover on top hinge. Support door and remove 3 bolts holding hinge. Lift door off lower hinge pin. Remove bolt holding both cam assy's and pry the one on the door out with the screwdriver. Replace both with the new cams, place door on lower hinge pin, place upper hinge pin into door, loosely insert the 3 bolts. Align the door, tighten the 3 bolts and replace plastic cap/bolt. Put the food back in the door and you're done. The only nut-driver needed is 5/16" and the screwdriver is only needed to pry out the cam that's located on the door itself.

Door wouldn't automatically close tight

  • Customer: Richard from Ashburn VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
If you have to push your door to close it and it doesn't close on its own, this is your fix. These door cams are two plastic pieces on the bottom hinge, one on the door and one on the bracket that goes to the body, that engage like a gear with only a couple of teeth. They are supposed to have raised teeth that engage to ride the door to a closed position when it is nearly closed. They are plastic and are made to wear down. To change, empty the door, then at the top of the door (i.e., looking down from above) unscrew two bolts that go to the hinge. The door then lifts off the bottom bracket. Put the door on a soft surface and unscrew the bolt that holds this cam. You can re-use the bolt. There is another cam bolted to the bracket that stays attached to the fridge. Change both cams at the same time. Reverse the process to re-install the door. Your door will close like new for under $10, in maybe 15-30 minutes.

Door Pop or clicking noise upon opening

  • Customer: LAWSON from AGAWAM MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
First I removed the top bracket cover screw with a 5/16" nut driver. placing it aside, I removed the three screws holding the top door hinge off using a 5/16" socket on a 1/4 drive to free the screws , then continued to remove them with the nut driver. placing them aside on top of the refrigerator. Then I lifted the door up and off the lower hinge and laid the door down on my kitchen counter. I removed the lower hinge piece from the lower bracket still on the fridge with a 5/16" nut driver and installed the new piece in its place and also applied a few dots of Vaseline on the lower hinge piece, I then removed the screw and lower bracket from the door and installed the new one and also applied some Vaseline on this piece also. I also took a rag that had been dipped in olive oil and rubbed the entire gasket surround the door to lubricate the gasket to keep it soft, then I reinstalled the door back onto its lower bracket, and then lined door back up correctly and reinstalled the top mounting bracket and screws then the cover, and then tested door. Door opens now with no noise and opens easier also.

Door would not stay closed

  • Customer: Troy from Reno NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched your video pull the door off switched parts and all done . Thanks to your web site it helped me diagnose and fix the problem
All Instructions for the 10654606300
1,126-1,140 of 1,196