Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10654606300 > Instructions

10654606300 Kenmore Refrigerator - Instructions

All installation instructions for 10654606300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10654606300
1,051-1,065 of 1,208
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker sensor did not see full ice bin.

  • Customer: Mark from Woodstock, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug the Unit first! Unscrewed the sensor covers on both sides. Snap off the old, snap on the new. Replace the covers and screws.

Icemaker leaking water and not making ice

  • Customer: Jake from Keller, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the Ice Maker

Unit Would Not Produce Ice

  • Customer: robert jr from east rutherford, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed hinged door from front of ice maker. Removed screws from bottom of ice maker. Removed ice maker unit and replaced control board. One pin connection was burnt. Reassembled unit and it works fine.

old ise maker was leaking

  • Customer: Richard from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed the steps in the video on your website, and was amazed at how simple and fast it was done, with no problems.

Ice door would not close

  • Customer: Richard from Springfield, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Ice door would not close thus letting warm air into the freezer compartment. Thinking the spring was broken, I ordered the Ice Door Kit. When it arrived, I dismantled the dispenser and installed the new parts. After installing all the new parts, I found that my problem was the "Y" end of the bracket that holds the spring pin. It was cracked and would not hold the pin. The bracket seemed to be molded into the panel on the outside of the dispenser. To replace the bracket, I would have had to replace the entire outside panel. I decided to repair the bracket and glue the broken piece. I used cyanoacrylate(CA)super glue that I use in model making. Even though that seemed adequate, I decided to drill a small hole through the bracket, perpendicular to the crack, and install a small screw to strengthen the crack. I also applied a little CA to the screw for good measure. It held fast and so far so good!

Replaced icemaker

  • Customer: Brian from Colchester, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We were reluctant to replace the icemaker on a 10-year old refrigerator that required a leak to be patched 2 years ago, but since the patch seems to be holding, we went ahead with the icemaker. Was about the same price as buying a portable icemaker and who wants that sitting on the counter?

Ice maker failed to make and dispense ice.

  • Customer: Mark from Minden, NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the broken icemaker. Removed the tray that is attached to the old icemaker and screwed it into the new icemaker. Then, I installed the new icemaker first by plugging in the control wires, then sliding the icemaker into the freezer, then screwing it into freezer. BY next morning, the icemaker made ice!

The plastic Ice Handle had broken after years of use

  • Customer: Tom from Hollis, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your web site was great. There was a short step by step video on how to remove and replace the ice door kit and tools required. The only additional tool I used was Blue Tape so I could stabilize the inner control panel out of way onto Door.If I need more appliance parts I now know where I am ordering from!!

ice maker went

  • Customer: Howard from Fort Myers, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered part and w/ help of a friend in it went.Devlivery was prompt. Receptionist on phone was great. If every company had one like her everyone would be a happy camper.Would recommend your company to anyone.It was a most pleasant experience.

Install new water supply tube

  • Customer: Robert from Las Cruces, NM
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Neither the OEM instructions nor any of the PartSelect videos explained BOTH ends of the tube for my particular appliance. All very thoroughly covered the obvious connection with the water valve from the wall. However, the push valve end for my KitchenAid is supposed to insert into the water filter chassis, which can barely be seen from the back of the appliance, much less reached with any tool. In order to make the repair, one must either remove the water filter chassis (which I attempted unsuccessfully), or put the appliance up on jacks in order to reach the push valve site.

icemaker does not make ice...mech cycles normally

  • Customer: Don from Lanham, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

Refrigerator was getting warm

  • Customer: Mack from Los Banos, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

Kick Plate Clip Broke

  • Customer: James from Virginia Beach, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

Icemaker replacement

  • Customer: Mr David from Arroyo Grande, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The replacement was easy, especially after watching the install video. Saved over $200 by purchasing the part at PartSelect and doing the install myself. Will use PartSelect again in the future.

icemaker stopped working

  • Customer: Thornton from Highlands, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I did not have voltmeter to test for problem. Internet sites suggested the most common problem is the circuit boards--a sender and a receiver which detect when the ice bucket is full. I could only buy as a pair (about $94). I removed two screws of cover of receiving unit, detached the coupler, replaced the circuit board. Icemaker now works. The sender was obviously still good.
All Instructions for the 10654606300
1,051-1,065 of 1,208