Models > 10654606300 > Instructions

10654606300 Kenmore Refrigerator - Instructions

All installation instructions for 10654606300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10654606300
886-900 of 1135
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Removal of old ice maker& instert new one

  • Customer: Robert from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed ice maker flap;using nutdriver removed screw/nut visible on right;pulled unit out until electrical visible; disconnected electrical;removed old unit;removed old unit from fram;(3-screw/bolts)assembled new unit on frame;reinserted unit&connected electical. Ice cubes formed in about 1hr.

Ice maker stopped working

  • Customer: Eugene from Danville CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
followed a movie on the internet. I'm 77 and I felt like it was very easy. My wife of 51 years gave me a round of applause when the first ice cube popped out.

Water would not flow into icemaker and icemaker would not work.

  • Customer: Kenneth from Rapid City SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions given by your demonstration. I took the back screw off, dropped the wire plastic cover. I then used the screwdriver to push the two (2)slots in and pulled the icemaker out and then unplugged it. I believe unplugging it was a little hard because the plug was pretty well sealed together and frozen. After finally getting the plug apart I then pulled the icemaker fully out. After pulling the cover off and putting it on the new one per your demonstration, I then inserted it back in. I stuck my hand behind the icemaker and bent the hose with my index finger and thumb so that it would drop into the water tray and then slid the icemaker back in until it snapped back in the slots. I then put the plug cover back on and reinserted the screw. I forgot to mention taking the front cover off before removing the icemake and reinserting it after replacing the icemaker. I would highly suggest customers follow your demonstration, it paid off well. I watched it about 8 times before I received the icemaker in the mail. Oh by the way water started flowing into the icemaker with 4 minutes and ice started coming out in about 30 minutes. As the icemaker got colder it started producing the ice faster. It's a sweet sound hearing the ice drop into the container.

Icemaker stopped making ice.

  • Customer: Ronald from Celebration FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Once it was determined that the icemaker was actually the problem two really good things happened. One, there was a video on the repair process on the web site. I wish I had viewed it before I removed the icemaker because it would have saved me about 10 minutes in that process. Second, I order the part on Friday morning around 10:00 a.m. and then went to the store to buy bag ice to get us through the weekend. On Saturday morning, the part was at my door ... yep, less than 24 hours! Everything was back in working order in about 15 minutes, part of that was my wife taking advantage of the shelf being out to do a little extra cleaning and reorganizing. Thanks for the video and excellent service. Ron Coulter, Celebration, FL

ice maker stopped working

  • Customer: Gary from Stillwater OK
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I took out the icemaker to see if I could find a problem and the ice tray coating was peeling, the tray heater was corroded and so was the motor assembly. I matched the picture on the site to my icemaker, checked the dimensions they gave and it was identical so I ordered it. Install was pretty easy and the icemaker started working within minutes. Thanks!

Ice maker quit

  • Customer: Billy from Cape Girardeau MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It was so easy, one screw to remove the plug cover, slide out unit, unplug, take off bottom by unscrewing 3 screws, place bottom on new unit, plug in, slide in place, replace cover, and let it get cold before turning on icemaker. The video on your site really helped.

My ice maker was not making ice

  • Customer: Alfred from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Based on research done on your site, I concluded that my problems was the icemaker control. The video showed me exactly what to do. During removal, I dropped the unit and broke the water fill cup. Ordered the control unit (as well as a replacement for the broken cup). Installed in about ten minutes. You really can't mess up. It only goes in one way! The next day, bucket was full of ice. Thanks for all the help. I figured I saved $200.00 on the cost of a technician call.

Ice maker stopped making ice

  • Customer: Mark from Coraopolis PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the simple steps in the awesome repair video!

Ice door assembly broken, freezing up ice maker

  • Customer: Sandra from Burlington NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

ice maker stopped making ice

  • Customer: Ronald from Hebron KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Web site is fantastic, I used web site to figure out my problem and order parts, I also used web site on how to install which made it a snap to do repair Ice maker up and running, all replacements parts were factory which fit perfectly

Installation of Replacement Ice Maker

  • Customer: Robert from Fernandina Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video accompanying the ice maker replacement part. Took 6 minutes. Then, having gathered my two recommended tools, moved to the fridge. Had the new replacement installed and working in 4 minutes. Doesn't qet any better than this.

Ice maker quit working, then the fridge & freezer stopped cooling

  • Customer: Ina from Altamonte Springs FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I actually purchased an ice maker, a combination start device & a run capacitor. I watched the 2 videos which were very helpful, in fact I may not have been able to do this if I had not watched the videos first. It took me step by step. It couldn't have been more simple. I replaced the start device & the run capacitor first just to make sure my fridge would cool again, then when it did, I replaced the ice maker. I saved myself a service call ($59.95) and the labor to replace the ice maker & other parts($140)and that didn't include the parts! By the way I'm female and 71 years old. So if I can do this anyone can.

No ice from ice maker

  • Customer: William from Moscow ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Parts Select has great videos that describe step-by-step how to perform the repair. I did a sloppy job of diagnosing the problem, and concluded it was the water valve. The actual problems was that the ice maker was not sending a signal to the valve to send water. I could have determined this if I had tested the ice maker using all of the connection points where a jumper wire could be inserted. The ice maker arrived on my doorstep exactly when promised, and was an easy ten-minute fix. My conclusion is that an average person CAN work on their own appliances with a company like PartsSelect to backstop them.

The icemaker stopped working

  • Customer: Patrick from gilroy CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaker and installed the new one. Went from six tiny ice cubes to four big ice cubes. Ice is of a higher quality, and the ice no longer falls out of the bin as the old ice maker's ice had once been prone to doing. A certified epic win on my part.

Water leaking and freezing on the botton of the icemaker mold

  • Customer: Richard from Jacksonville FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Install was done in reverse order of uninstall. The only thing that made this install a bit tricky is that the fill cup on the replacement icemaker was not the same part as on the original. I could have attempted to trim the replacement fill cup but didn't know how well that would work. I instead elected to install the original fill cup onto the new icemaker. This added a bit of time and complexity to the repair but I followed a repair video for when just the ice mold is being replaced. That video told me how to disassemble the ice mold and timer motor which had to be done to in order to replace the fill cup. It's been about 2 weeks since repair was made and the icemaker seems to be working properly.
All Instructions for the 10654606300
886-900 of 1135