10654606300 Kenmore Refrigerator - Instructions

I ordered both the Ice maker and the control boards as It was for a rental and I did not want to make more trips then necessary to repair. I installed the new control boards and the ice maker and the refrigerator now makes ice.

Replaced both the control cards and the ICE maker and now it is working fine

Followed the lead of david from chesterfield in prying off out cover, unplugging it and setting it aside. Unscrewed and pulled out next assemply, and taped it above work area to avoid having to unplug. The pried pulled out pin to right holding ice door hinge to remove old unit. (Notice which way the spring faces before removing!) unplugged it. Ended up taking off push-dispenser handle (one screw on right) to get easier access. Then reinserted long pin being careful to have spring with two long tongs pointing down. Then put everything back together. Use all parts!

I watched your youtube repairman twice. the video was very good concerning how to do the replacement.Thank you very much this is a lifesaver for people like myself that can not afford a repair person to fix broken items at the house.

My ice maker stopped producing ice after our refridgerator was accidently turned off for 4 days. Note: the on off switch in the front does turn the unit off even though the light stays on, why we need easy access to turn off the fridge is beyond me. Regardless, I spent way more time researching the problem then doing the repair. There is 2 things that could be wrong: 1 was the infra red light located on either side of the freezer, called the transmitter/reciever. 2 was the side of the ice maker control panel. Either one or if I had to replace both it would of been less then the cost of a repair man to come to my home. Prices here a good. I started with learning the diagnostic of the ice make which is learned by watching the red light flash. That informed me that it was working ok. Reference: if you hold back the hinged plate and pretend the door is shut the light should flash, flash, pause. This means its working. I went with the other route of the control module on the ice maker. This part came fast like 2 days. I watched the video on the parts web page and it was simple to do. You do have to wait until the temp goes down below 15 degrees in order for the ice maker to kick in. I won't buy another kenmore for I have had plenty of trouble with this one and its bearly 6 years old. I'm Definetly a fan of this website. Good luck DIY ers!

Super simple repair, as it takes only a direct replacement of the valve. Removing and replacong the sdrews on the access cover took the majority of the repair time. Two screws retain the valve, and two electrical connections are very simple and easily reached. I would recoment using good sharp side cutters instaed of a knife to cut the three water lines.

I looked on line to see repair instruction videos on my refrigerator ice maker. When I saw how easy I went to PartSelect and order the part (control and motor assembly). I received the part in two days with the cheapest shipping option. My 33 yr old son was visiting when the delivery was made. After we opened the box, he went to the basement for tools and the rest is history. 10 minutes work and ice a couple of hours later! No problems since.

This was easier than I made it. remove air diffuser cover at the top side of the freezer. remove air deffuser by closeing clips on freezer side. disconnect the power supply. reverse procedure. not real specific but you can figure it out I know you can.

I ordered a new ice maker from Partselect which arrived the next day with standard shipping. I opened PartSelects installation video on my iPad next to the refrigerator and stepped through the installation. It was as simple as removing and replacing four screws.

Pulled out the old unit removed 3 screws waited about 3-4 hours had ice. Took over night until we were actually sureby then the ice bin was full. Easy repair!

simply replace the compressor start and delay

Couldn't snap the track in no matter how much pressure I exerted. Was afraid I would break the plastic. Maybe it was the wrong part. Found a suggestion in the partsselect tips area. Used a nail file to slowly sand/grind down the plastic hubs. Took my time doing each one several times. Tested installation after each round of sanding down, so as not to go too far. Eventually (5 or 10 minutes of sanding) it popped right into place. What was even more amazing to me is that I ordered the part around 2P.M. on Friday and it was delivered to NJ the next day(Saturday) before noon.

The repair was surprisingly easy. Definitely much cheaper than calling a repair man! Very pleased with PartSelect....speedy shipping and great customer service. Would do business with you again, if need be.

Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

We used the you tube video on your website. It was so helpful! Sears wanted to charge us $450.00 for a 10 minute repair job, insane! thank you Part Select for saving us a ton of money.