Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10654582400 > Instructions

10654582400 Kenmore Refrigerator - Instructions

All installation instructions for 10654582400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10654582400
1,156-1,170 of 1,561
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice machine not working.

  • Customer: Thomas from Naperville, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on how to make the repair. It was that easy. The hardest part was disconnecting the electrical. Once that was done it was a really simple fix.

Ice Maker stopped working

  • Customer: Hector from San Diego, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Its the easiest repair in the world to do. Took less than 15 minutes. Removed the Icemaker unit from friedge, removed 3 screws replaced motor (very easy to do), 1 hr later I had Ice again! =)

Ice maker stopped making ice

  • Customer: Vonnette from Bixby, OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unscrewed bolts pulled out motor,unhooked motor,replaced with new motor,put back in and replaced screws..fairly easy..then we had ice that evening!

Not making ice

  • Customer: Thomas from Orlando, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Video instructions walked me right thru it had no problems.

stopped producing ice

  • Customer: Walter from Palm Beach Gardens, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as shown in the video; had a bit of trouble with the wiring harness, but all else went smoothly. If it were not for the explicit video installation instruction, it could not have been done by a do-it-yourself guy with tools. I had ice again in 3 hours! PartSelect is the absolute best when it comes to diagnosing, ordering and installing the part(s).

Our ice maker has not worked for years. My husband tried to repair it back then and now we know that he actually broke it. On the front of motor control there is a dial that says "DO NOT ROTATE'. It means do not rotate.

  • Customer: Linda from Colonial Beach, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
He removed the front of the motor box. He then took the motor panel off and replaced it with the new one! So easy!! We have been buying ice or getting it from a friend that has a commercial ice maker. I could not believe it was that simple and the delivery was unbelievable. I ordered the part either Thursday or Friday and FedEx delivered it Saturday! Thank you so much. Now I have all the ice I need!!!

indtalled new part WPL W10190935 and it did not fix problem

  • Customer: Ronald from Jeffersonville, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
as shown in instructions

Ice maker sounding like it was going to release ice, but not doing so.

  • Customer: Bridget from Clinton, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was the easiest repair I have ever done. Don't waste your money calling a repairmain for this one. Unplug from electrical outlet, and turn off water supply. I first removed the ice bucket to give myself the room needed to remove ice maker. Then I loosened to two top nuts holding the icemaker and removed the bottom one. Pulled the icemaker away from the freezer wall and disconected the power supply. Removed unit from freezer and removed the three screws holding control motor assembly in place, gently removed icemaker control assembly. Secured with the three screws, placed unit back in freezer making sure water inlet was in place and reconected power supply. Slid unit onto the top two nuts and tightened and replaced bottom screw. Turned on water supply and reconected to electrical supply. Easier then pie.

Icemaker stopped making ice

  • Customer: Bruce from Camarillo, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the icemaker assembly, which was simple to remove. Once the assembly was removed, I unscrewed the motor housing and replaced it. I then reinstalled the assembly and closed the door. It did not making ice immediately and it took about 30 minutes to start.

ice maker wasn't

  • Customer: Mona from The Sea Ranch, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

Unit stopped making Ice

  • Customer: Denis from Columbia, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found my unit had stopped making ice. I did 20 min. of search on the internet and found this site. I was going to just buy the whole ice maker unit, but after reading a bit more found that the majority was just the motor assembly. I ordered it, 2 days later it was at my front door. I pulled the ice maker unit out, took off the motor assembly, and low and behold a small whit ppiece of plastic fell out. I replaced the motor assembly re installed the ice maker and in one hour I had ice again. As far as ease to do this job from 1 being hard and 10 being super easy, I would rate this a 10+. If you have this kind of problem, I would not waste your money on a repair man, 150.00 service call, Hell no. 65 bucks and your done. Before your wife can make you a pot of coffee this can be out and back in. I don't want to take money away from the appliance repair men but some repairs can be a DIY project. Nut driver and phillips screw driver is all you need.Hope this helps ya.

timer motor died

  • Customer: Paul from Moline, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas

No water coming into ice maker

  • Customer: Ricardo from Hialeah Gardens, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.

Compressor would not work

  • Customer: James from Lucas, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I spoke with a friend of mine who does refrigeration and he suggested that I check the starter. I pulled it out and read your site to confirm the problem. The starter had loose particles just as your site mentioned. I ordered the part on Wed. afternoon and received it the next morning. When it came I received two different pieces which allowed for a product upgrade if needed. It wasn't and after I put it in it worked great. Freezer to -20 degrees F. Thanks...JT from Lucas, Ohio.

Refrigerator and freezer both stopped cooling

  • Customer: Patrick from Green Valley, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I read prior postings about how the compressor start relay was the most likely failed part based upon the periodic clicking as well as the rattle when the relay was shaken, with loose metal particles coming out of the original part. I ordered the replacement for next business day delivery and it arrived on schedule. The replacement kit comes with two relays for two different compressor designs. The correct relay is an exact replacement for the original, with the same part numbering. I removed the compressor start capacitor (a small black rectangular box with two metal terminals) from the original relay and installed it on the new part. The replacement kit comes with a black plastic cover, which did not fit since the start capacitor is in the way. I reinstalled the wire hook that secures the relay to the compressor body, and the refrigerator now works great.
All Instructions for the 10654582400
1,156-1,170 of 1,561