Models > 10654536400 > Instructions

10654536400 Kenmore Refrigerator - Instructions

All installation instructions for 10654536400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10654536400
1,516-1,530 of 1,530
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refridgerator door would not close easily.

  • Customer: John from Battle Creek MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I unloaded the door, removed the cap covering the screws at the top hinge. I removed the screws then lifted the door off the pin. Next I removed the screws holding the door cams in place. Replaced both cams and screws, set the door back on the pin then reinstalled the three screws at the top. Snapped back on the cover and I was done. Door works perfectly.

Very loud clicking noise when opening/closing door

  • Customer: Ben from Port Saint Lucie FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

The door would not close completely

  • Customer: Roger from Punta Gorda FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

ice no longer came out when using the door dispencing.

  • Customer: JOSEPH from RAEFORD NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair went extreamly easy and exact to detail. I followed the video step by step, and that turned the assembly into a professional job.

Refrigerator Door Wouldn't Stay Closed

  • Customer: Robin from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

The refridgerator door would not shut on its own. It had to be pushed completely shut every time it was opened.

  • Customer: Fred from Dacula AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went to the PartSelect online videos and watched this one: "Refrigerator Repair - Replacing the Door Closing Cam (GE Part# WR2X4901)," to assess whether or not this could be a do-it-yourself repair. Even though the subject of the video was demonstrated on a refridgerator model different from mine, it appeared similar enough for me to get the idea of how to accomplish the repair, so I used the PartSelect site to guide me to the parts needed to do it. The parts came in and I once again watched the video and then proceeded with the repair. The repair was very simple and easily accomplished - took a half hour total. If you watch the video referred to above, you'll see exactly the way I did it. My experience precisely mirrored that shown in the video. One hint: I did spend some time wondering if I should have emptied the refridgerator before starting the job, and decided not to. It was the wise choice as the job went so fast, removing all the food would have been a waste of time. The door was off maybe 20 minutes total, and that was only enough time to raise the temperature inside about 5 degrees, which was quickly recovered when I re-installed the door. I can't say enough good about the PartSelect site, for the superb guidance in parts selection, as well as the extremely helpful how-to videos. I probably would not have attempted the repair on my own if not for the help this site provided. Thank you very much for this valuable service.

Door would not close by itself

  • Customer: rich from liberty twp OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed instructions on this website. Only difference I placed a couple blocks under the door to keep it from dropping & removed both cams at the same time. No need to remove the door from the unit.

Door no longer closing on its own and remaining slightly ajar.

  • Customer: Gil from San Ramon CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
This is a very easy fix. Begin by emptying the contents of the door. Then, just remove hinge cap and remove the three hinge screws. The door can then be lifted off the hinge pin and placed on its side. Once this is done, replace the two can pieces (one on the door and one on the frame). Then just lift the door back in place and secure the hinge. This job can be done by one person (maybe two if you need help place the door on a work surface) and will take just 15 minutes.

Door was not shuting al the way buy itself

  • Customer: Edward from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Took out the door bins, 1 bolt on the plastic cap, 3 bolts on the hinge, took the door off, replaced cam at the bottom, all same size bolts, reset the door spent longer time cleaning the door selfs all done by my self in less than 30 min. others said it helped to have second pair of hands "my wife would of just got in the way :)"

Refrigerator door not staying closed.

  • Customer: Daniel from Citrus Heights CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The refrigerator door was not staying closed. Arriving home we found it open and not running. The compressor was off on thermal overload. In checking that and while cleaning the condenser I noticed the refrigerator door was 1/4" lower than the freezer. I saw how the door cams worked to keep the doors closed. The installation was easy. I blocked up the door. Removed the old cams using a small socket and installed the new. Door cams tool less than fifteen minutes.

Refrigerator door not closing on it's own

  • Customer: Kurt from Terre Haute IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Lower door closing cam was completely worn down so door wouldn't close on it's own. Ordered parts which arrived in a couple of days. After watching installation video on this website the job looked pretty easy. Needed socket wrench to loosen nuts at top, they were really tight. Removed door. Replaced both the cam on the bottom of door and the cam on the main unit, put door back on making sure it was straight and lined up properly. Retightened top nuts securely. Voila, problem fixed in only about 15 minutes or so.

Door would not close on its own anymore

  • Customer: Richard from Midlothian VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
internet search

Loud knocking noise when opening door

  • Customer: William from Land O Lakes FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the nut holding the plastic cover plate at the top of the door. Removed the 3 nuts holding the latch to the fridge. Lifted the door up and laid it on its' side. Removed the nut holding the door cam and replaced it with the new one. removed the nut holding the lower door cam and replaced it. Put a little vaseline on both cams and re-in-stalled the door. Took less than 15 minutes and the door is like new. Watching the video on the web site was perfect.

Refrigerator door would not self close

  • Customer: Robert from Palo Alto CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed food from door. Shut off fridge. Removed dust cap at top hinge. Marked location of top hinge with masking tape so lining up when reassembling would be easier. Removed screws holding top hinge to fridge. Removed door, placed on blanket&towel. Removed old door cam. Put on new door cam. Removed old hinge cam. Put on new hinge cam. Put door back on. Replaced top hinge, lining up with tape. Replaced dust cap. Note that door did not really self close very well until it was filled with food. By far the hardest part of the whole operation was that my wife wanted to clean the fridge in the process!

Refrigerator Door wont close

  • Customer: Peter from Saratoga Springs NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Followed the Partselect instructions - removed door, removed old cam and replaced with new cam. One lesson learned. There are two cams - one that sits on hinge below door and one that is up inside bottom of door. If you are replacing one, replace them both.
All Instructions for the 10654536400
1,516-1,530 of 1,530