Models > 10653232300 > Instructions

10653232300 Kenmore Refrigerator - Instructions

All installation instructions for 10653232300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10653232300
16-30 of 1397
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

icemaker leaking infreezer compartment

  • Customer: John from Oberlin LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 73 of 89 people found this instruction helpful
first I backed off top two screws and removed bottom screw. unplugged wire harness. removed old icemaker. harness on new icemaker was the same. plugged in hung new icemaker on top two screws installed bottom screw. turned water on job complete and very easy. I was very satisfied with the whole process.

Warm Air Getting Into Freezer

  • Customer: David from Chesterfield MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 69 of 86 people found this instruction helpful
Patience is a virtue. The kit really works. 1st, lift the front plate of the ice dispencer by placing a flat head screw driver into the two slots at the bottom of the panel. When the panel is lifted up slightly at the bottom, push up on the panel to remove it. Careful not to break panel and the wires attached. Next, remove the wiring panel by removing the two screws on left and right sides. Then, unplug the old black ice cover from the wiring panel (this is the heating plug that you will nolonger need). Next, remove the parts and replace them with the parts in the kit, noting where each part comes from, etc. All parts in the kit are necessary and should be used. Some of the replacements need trial and error. Patience will be important. Also needed is a person that loves to solve problems, especially because the kit does not come with instructions. But the kit definitely works!

Ice Maker stopped working

  • Customer: Robert from Port Washington NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 63 of 73 people found this instruction helpful
With socket wrench un-screwed the 3 screws and pulled out the ice maker assembly.

Pulled off white plastic end-cap and noticed the plastic gear disk had snapped off (sub part # R0167202)

However, it is all-one-part of the motor assembly unit # w10190935 (part # PS2341896) which must be ordered as a complete part.

Unscrewed the motor assembly (3 screws) with phillips head screw driver.

Screwed in the new unit.

Placed ice maker back into location and tightend the bacing srews.

1 hour later ice was falling!

where ic e dispencer spring is held to door broke at mold

  • Customer: helen j from murrells inlet SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 59 of 71 people found this instruction helpful
after ordering ice dispencer repair kit, and removing the outer parts found out that the problem was the ice dispencer door shell . this part is no longer available.It seems to me that if whirlpool wants to have return customers they have to stand behind the product. Well I made a L bracket and drilled a hole to to recieve the spring keeper and glued this to the housing and used a 3 1/12"finishing nail as the pin all works fine

water slowly leaking from fill tube- overflowing ice tray

  • Customer: Michael from Franksville WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 49 of 54 people found this instruction helpful
unplugged fridge, turned off water supply, disconnected water supply line (towel to catch drainage). remove cardboard lower panel from back of fridge. remove 2 bolts holding existing water inlet valve assy to fridge. Disconnect 2 electric plugs from assy. water lines disconnect using push/pull method (mark where they go). If any water tube line has any surface imperfections trim off a small length of line using a razor knife (cut tubing perpendicular (or "square" )on the end. I had to remove small unused part from the new water inlet valve assy. Insert the 3 water lines to the correct spots: push them on,fully, give a tug to make sure they are connected fully. Reattach the 2 electrical plugs.Bolt the unit back in place. I connected the water & plugged it in, filled about 10 glasses of water and made sure an ice cycle ran, to check for leaks (none found). I cleaned off some of the dust on the back of the fridge, reattached the cardboard lower piece. and listened to the sweet sound of Ice filling, and not my wallet emptying to the service man!!

No water from front dispenser, ice still working

  • Customer: Trent from Richmond VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 53 of 68 people found this instruction helpful
First checked to make sure the water reserve line inside fridge wasn't frozen (soaked coil at back of fridge in a container of warm water for 10 min). That seemed fine and icemaker was still working so assumed that portion of the water inlet valve feeding water line wasn't working. Video on PartSelect website showing how to replace the valve was spot on and gave me confidence to install myself. Part arrived within two days and installation was done in a snap exactly as shown in video. All the lines & wire harnesses fit perfectly, water & ice working great, and I couldn't be more pleased.

The compressor would shut down and not restart unless you tapped the temperature knob which i did for about 3 weeks before ordering this part

  • Customer: michael from clarksville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 46 of 50 people found this instruction helpful
Was pretty simple just take the knobs off pull off the face plate remove a few screws and drop the whole shelf down. then a few more screws down the side to the back of the fridge. Pull the sensor wire out of some styrofoam and pull off the plastic coating and slide it over the new one and install it in reverse order from taking it out. Works great now and i have ice everyday :)

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 47 of 60 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.

Icemaker made a clicking noise then quit making ice

  • Customer: Ryan from Layton UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 43 of 57 people found this instruction helpful
Motor from Part Select was 185W instead of 260W that came out of unit. After a bit of searching online, I found out the 260W had been obsoleted for lack of torque when harvesting ice.

Removal instructions: Unplugged fridge. Then I removed the screw on the bottom right rear of the unit. Then removed the plastic cover that covered the power connector. Pulled out the icemaker by pushing in the tab on the bottom left middle of the icemaker unit and pulling unit toward me. Unplugged the connector on the back right hand side. Removed the cover on the left side covering motor. Took out 3 philips screws and removed old motor with broken axle that spun freely (the source of the clicking noise). Put new motor in aligning harvest arm (the thing with the fingers) and did reverse of removal. Then plugged fridge back in and it started a harvest and the next morning I had a half tub of ice.

No ice in ice trey

  • Customer: Wayne from Leesburg FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 36 of 41 people found this instruction helpful
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.

Refrigerator was not cooling properly.

  • Customer: Eddie from Gretna LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 32 of 34 people found this instruction helpful
I removed both plastic knobs from assembly faceplate. Then I loosened the screws holding thermostat housing to upper cabinet of fridge. Following this step, I loosened the screws of the thermostat to remove it. Next was the removal of the plate and vent pieces holding the thermostat wire sleeve in place. After removal of thermostat from sleeve; all steps were reversed and unit was up and running normal (cooling) with no problems. "Ahh, it's nice to have cool again "

Icemaker would not stop putting out water, then would not make ice

  • Customer: Phil from Felton DE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 34 of 41 people found this instruction helpful
First, I unplugged the power to the entire fridge, and then removed the ice tray and ice door. Next, I unplugged the flat plug in the very back left behind the icemaker. Then I removed the 1/4" hex head sheet metal screws (2) and the phillips head screw (1) that hold the icemaker to the left side of the freezer wall. New icemaker came with a different style trip arm, so I used it. Plugged new icemaker in before reattaching it with the same (3) screws. Replaced ice tray and door, plugged in fridge, and waited....Dumped its first batch of ice maybe a couple of hours later. Not much trouble-shooting is needed when the entire icemaker is as easy and relatively inexpensive to replace as this. Twenty minutes, max.

Previous owners of the condo took the two drawers from the refrigerator

  • Customer: Betty from Orinda CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 33 of 39 people found this instruction helpful
No repair, just slid the drawers in their places.
Since you had a diagram of the refrigerator parts, ordering the parts was easy and I was confident that the parts were the correct ones.

Ice Maker Stopped Making Ice (No Water)

  • Customer: John from Vernon CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 32 of 37 people found this instruction helpful
The repair was made simply by removing the old broken Water Inlet Valve (two screws and 4 tubes) and replacing it with the new one. All the tubes and wiring are the same so it was relatively easy to replace. Now we have fresh made ice again

No Cooling

  • Customer: Gregory from Portland OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 31 of 34 people found this instruction helpful
I noticed the fan was running but not the compressor, they are wired in series meaning the compressor should also have power and you should hear the compressor. Could not hear compressor coming on, removed the white relay attached to the side of the compressor and could hear loose pieces shaking in relay. Ordered new relay and plugged it in, took less than five minutes. Very Easy. Thank you Partsselect
All Instructions for the 10653232300
16-30 of 1397