Models > 10652603100 > Instructions

10652603100 Kenmore Refrigerator - Instructions

All installation instructions for 10652603100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10652603100
1,231-1,245 of 1,317
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door to the ice shute broken with worn out parts.

  • Customer: Edward from San Antonio, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took two screwdrivers and inserted bottom of bezel pryed up and out gently. Removed (4) screws and unpluged (3) electronic plugs removing the circuit board. After you remove bezel & circuit board you have a chance to see what you are doing and get to the problem area with more ease. Remove old parts and reverse it putting the new parts. Process is very simple just pay attention to the order everything was removed. On my frig one of the plastic ears that hold the pin which holds the spring and door was broke. The piece I needed was no longer avaliable. I had to use a piece of the plastic from the old parts I removed, drilled a hole the size of the pin in it and glued it to the broken off ear. Put everything back together and I am pleased to say that everything works fine! So you might need to go a little MacGyver on it. All in all very simple fix.

ice chute door was warped allowing warm air into chute causing freeze up of chute. Would my dispense ice.

  • Customer: Peter from Westminster, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched Parts Select YouTube video for demonstration of installation. Went smoothly.

When I placed the glass cover in a sink of lukewarm water, it shattered

  • Customer: Mary from Sacramento, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I did was removed the stickers and place it in the frame - no tools required. It fit perfectly and is since it is clear (the original one has a grid pattern in it) I can easily see everything in the drawer below. I will be more careful in cleaning this one - apparently the temperature difference from cool to warm caused it to break, so I will just wipe this one down rather than submerging it in water.

glass broken

  • Customer: Kenrick from Lake Arrowhead, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The glass cover came on time and in good packaging. I removed it from the packaging and slipped in to the shelf. It fit perfectly and was extremely easy to do. We are very pleased with the entire process. Thanks

Ice maker was not making ice

  • Customer: William from princeton, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
used the video on your web site. also read the overview made things really simple

In the Door Ice Maker stopped working

  • Customer: Ed from Germantown, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions on the information sheet provided as well as watching a demo video on YouTube. Actual replacement of the emitter and receiver boards took only 5 minutes, but I was not sure it was working till I could here the ice maker harvesting the cubes. Still wanted to be sure so I kept an eye on it for a few hours. Each time I looked in there was more ice. I am so glad I found your website. Parts were about $106. Labor would have cost that much and the repair guy I talked to on the phone said he would probably have to replace the whole unit.

ice maker was not working

  • Customer: LINDA from FARMINGDALE, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I called in a repairman, who wasn't sure what the problem was but suggested it "might" be the electronic control boards. He charged me $55 for the service call, which I initially thought was reasonable. Then I found your website purely accidentally. I watched the video several times and read all of the comments posted. I then decided I would wait to see what the repairman would quote me for the part and the additional labor charge. He told me the part was $125. and the additional service charge was another $75. I decided to order the part, which arrived in 2 days. I am a woman who has never repaired anything on my own, but I decided to take a chance with this. It took me about 20 to 30 minutes to install both parts and within a few hours the first ice cubes fell. I was so proud of myself and very pleased that I found your website. The price of the part was reasonable, the video was very straightforward and all of the comments were extremely helpful. Thank you.

No ice production.

  • Customer: Paul from North Cape May, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We had cleaned the electronic eyes off several times which yielded one or two days of ice production. Since we could tell the ice maker was receiving water and producing ice we went ahead and replaced the controller. Now the ice maker is working like a champ. The instructions were easy to follow and the part was delivered quickly. Unplugged the fridge. Three screws on opposite sides of the freezer, plug in the emitter and receiver boards and replace the screws. Plug the fridge back in and away it went.

Ice maker was not working (door ice container)

  • Customer: Frank from Williamsburg, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. I first confirmed that the problem was a bad Infrared Ice making control board (Watched flashing of red light on right side of freezer - solid light would not occur when holding flap on left side of freezer). 2. I unplugged refridg,3. unscrewed both sides of the control unit and disconnected wire clips to the electronic boards. 4.popped in new Boards on both sides and connected clips onto each board. 5. Screwed the boards and covers to walls of freezer. 6. Plugged power back into wall and checked Red light again (when holding flap in, a continuous red light verified it would work). closed freezer and shortly ice was being made. Simple process. (careful using Screwdriver to help take wire off of boards - a small clip holds wire clip on - you need to stick screwdriver into back of clip while unconnecting). Easy and my ice worked perfectly.

Missing kick plate after a move.

  • Customer: William from Decatur, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Located part on your easy to use and understand site.Ordered one day and received the next (less than 24 hours). Easy to install. Very pleased with this seller...A+.

ice maker door failed to close causing frost to form preventing proper operation of icemaker.

  • Customer: Melinda from Owasso, OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Found video on YouTube. Ordered part from partselect. Part arrived and viewed video to refresh memory. Our refrig was a little newer than the video but the process ww was the same and quite simple after viewing the video.

Ice dispenser door dislodged/broken-causing ice/frost in freezer

  • Customer: LAWRENCE from Gig Harbor, WA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

Refrigerator Freezer Ice Door Broken

  • Customer: Peter from Wildomar, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Job went as per your terrific video. Except that when attempting to retrieve the old heater element the glue on the old door was no long pliable. I had to literally tear the old foam apart to get at the heater element and almost damaged it. Not to worry. It worked out well and all is great. Thanks for the very instructive video.

When you pressed on ice maker to get ice it was hard to get it to dispense

  • Customer: Dennis from Gig Harbor, WA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed along with the Video from the web site. I used the masking tape to keep the electric parts out of the way. one of the attaching points for the new ice door broke off so i used J B Weld to reattach it. then the repair was finished with out a hitch. The time was extended by the need to wait for the epoxy to cure

Ice dispenser was broken

  • Customer: Helen from Escondido, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My handyman did the repair. It was pretty easy for him. It would have been a real puzzle if we had not watched the video instructions. The new parts were slightly different than the old parts, but they fit perfectly. I thawed the frost buildup around the ice door and the opening of the ice bin with a hair drier, to get the ice to come out properly. Thank you so much for the video!
All Instructions for the 10652603100
1,231-1,245 of 1,317