Models > 10652603100 > Instructions

10652603100 Kenmore Refrigerator - Instructions

All installation instructions for 10652603100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10652603100
1156-1170 of 1240
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker wasn't

  • Customer: Mona from The Sea Ranch CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

indtalled new part WPL W10190935 and it did not fix problem

  • Customer: Ronald from Jeffersonville IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
as shown in instructions

Ice maker sounding like it was going to release ice, but not doing so.

  • Customer: Bridget from Clinton ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was the easiest repair I have ever done. Don't waste your money calling a repairmain for this one. Unplug from electrical outlet, and turn off water supply. I first removed the ice bucket to give myself the room needed to remove ice maker. Then I loosened to two top nuts holding the icemaker and removed the bottom one. Pulled the icemaker away from the freezer wall and disconected the power supply. Removed unit from freezer and removed the three screws holding control motor assembly in place, gently removed icemaker control assembly. Secured with the three screws, placed unit back in freezer making sure water inlet was in place and reconected power supply. Slid unit onto the top two nuts and tightened and replaced bottom screw. Turned on water supply and reconected to electrical supply. Easier then pie.

Unit stopped making Ice

  • Customer: Denis from Columbia IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found my unit had stopped making ice. I did 20 min. of search on the internet and found this site. I was going to just buy the whole ice maker unit, but after reading a bit more found that the majority was just the motor assembly. I ordered it, 2 days later it was at my front door. I pulled the ice maker unit out, took off the motor assembly, and low and behold a small whit ppiece of plastic fell out. I replaced the motor assembly re installed the ice maker and in one hour I had ice again. As far as ease to do this job from 1 being hard and 10 being super easy, I would rate this a 10+. If you have this kind of problem, I would not waste your money on a repair man, 150.00 service call, Hell no. 65 bucks and your done. Before your wife can make you a pot of coffee this can be out and back in. I don't want to take money away from the appliance repair men but some repairs can be a DIY project. Nut driver and phillips screw driver is all you need.Hope this helps ya.

timer motor died

  • Customer: Paul from Moline IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas

No Ice

  • Customer: Rodger from Fort Washington MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove icemaker control assembly, replaced with new one.

ice tray wouldn't fill with water

  • Customer: Ken from garden city ID
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I shut the water relieved the water pressure. unplugged the refrigerator removed the electronic control board and emitter.there was one screw i took off on the right rear side of the ice maker to remove a wire connector cover .then on the left front bottom side of the ice maker assembly i took a flat head screw driver gently pushed up on the plastic clip and it pulled straight out disconnected the wiring harness put the new icemaker control motor assembly in.put the assembly back in.the new emitter and receiver boards in turned the water and power back on.it took about a hour before the ice tray filled up with water and started doing it's thing very easy fix.

Ice maker doesn't make ice.

  • Customer: Lowell from Discovery Bay CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Changed the Motor Assembly. Wasn't the problem. If I had followed your trouble chart a little farther I would have found out it was the circuit boards. All is well and I might add that yor guide with the parts and video are priceless. Very Happy. Lowell Onstad

Freezer stopped making ice cubes.

  • Customer: Mark from Williamstown NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
At first I thought the problem ws with the water valve. I tested it and got a normal reading. Just as Partselect suggested, it was the Icemaker Control and Motor Assembly. Once I removed the old one I noticed it was dry rotted on the plastic stem that turns the wheel. I tried to replace it while it was still in the freezer. That didnt work very well so I ended up taking the whole ice maker out as shown in the video. Once everything was back together and plugged in I heard that sweet sound of water flowing down the chute into the ice maker. About 4 days later the ice bucket was full to the top with ice.

My ice maker was not making ice

  • Customer: Alfred from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Based on research done on your site, I concluded that my problems was the icemaker control. The video showed me exactly what to do. During removal, I dropped the unit and broke the water fill cup. Ordered the control unit (as well as a replacement for the broken cup). Installed in about ten minutes. You really can't mess up. It only goes in one way! The next day, bucket was full of ice. Thanks for all the help. I figured I saved $200.00 on the cost of a technician call.

Ice maker stopped making ice

  • Customer: Mark from Coraopolis PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the simple steps in the awesome repair video!

Fan became noisy and started wobbling.

  • Customer: James from Cave Creek AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Condenser Fan was making noise

  • Customer: Kerry from Franklin TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

Condenser fan vibrated loudly while turning

  • Customer: Robert from Aurora IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the back panel covering the fan and condenser off the refrigerator (just a few screws) and disconnected the fan which was a simple plug. The fan was held in place with three screws which I took out. I pulled out the old fan and replaced it with the new one, three screws to secure it in place and reconnect the fan plug. Then simply replace the back panel and plug the frig in. the fan silently started right up. Good as new and no service call! :)

noise coming from back of refrigerator. determined it was the fan

  • Customer: BRUCE from SOUTH WINDSOR CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.
All Instructions for the 10652603100
1156-1170 of 1240