Models > 10652603100 > Instructions

10652603100 Kenmore Refrigerator - Instructions

All installation instructions for 10652603100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10652603100
1,141-1,155 of 1,317
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

plastic gear in ice maker was broken

  • Customer: Chieu from Suwanee GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Just watch video from part select and following the instruction to replace the control and motor assembly.

Ice Maker stopped making ice. A clicking sound was coming out of the unit.

  • Customer: Richard from Tomball TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the ice maker unit completely from the freezer, following a Utube repair video that I found. I originally thought it was just the control board that was defective, because on examination, found a burned-out copper trace on the board, as well as a burned-out plastic connection point. Installing the new parts was a breeze. This icemaker is pretty foolproof, with plastic tabs that line up with the housing. a matter of lining up the screw holes was all that was necessary. Only problem I had was attaching a plastic cover that shields the electrical connection from the water. Once all was installed, I had to wait overnight for the icemaker to make ice. We've had ice ever since! Thank you Partsselect for very courteous and fast service!

Wasn't making ice.

  • Customer: Carol from Brooklyn NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered both icemaker motor assembly and the emitter and receiver (sensors)as I was uncertain as to which was the culprit. We couldn't unplug the frige as it is heavy, so we shut the circuit breaker until we were done with the repair. The icemaker motor was a bit clumsy to remove. My refrigerator was entirely different than the one on the video I viewed, as I have a side by side and the video was of an entirely different model. The video's icemaker was not as clumsy to work with. My husband was a little apprehensive so I rode shot gun and assisted and he did great. He did change the motor first and probably should have waited to see if it worked. He didn't wait, and went ahead and changed the sensors....that was a breeze. We waited about 2 hours and lo and behold once the freezer went down to 14 degrees, the icemaker began it's magic and we had a full supply of ice within 24 hours. So, I saved quite a bit of cash by purchasing the parts I needed at Parts Select and eliminated the repairman's expensive fee. Very happy with end results.

Icemaker stoped making ice.

  • Customer: Henry from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
There are two tabs that hold the icemaker to the rails it sits on. I use a small screwdriver and pushed the tabs up to release the tray and slid the Ice maker out. the cover over the control motor just pops right off. Then I removed three screws from the control motor pulled it off and put the new on, replaced the screws and put the cover back on and slid the icemaker back into the rails. I shut the freezer door and within the five minutes it took me to put my tools back in the garage, it was dumping ice. Very easy to fix. You do not need to remove the screws that hold the icemaker to the tray.

ice maker stopped making ice.

  • Customer: Rliot from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removedicemaker and unscrewed 3 screws hill ding motor assembly and control module to ice maker . nstalled new part and attached it with the 3screws. reinstalled ice maker and ice making cycle began almost immediately.

no ice cubes

  • Customer: Linda from Pawhuska OK
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your youtube repairman twice. the video was very good concerning how to do the replacement.Thank you very much this is a lifesaver for people like myself that can not afford a repair person to fix broken items at the house.

no ice, motor not running

  • Customer: Randy from Mesa AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaker, replaced motor and reinstalled. Very quick delivery of parts, fit perfectly.

ice maker stopped making ice

  • Customer: harold from new faifield CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the motor control assembly and it works great

Ice maker made ice but would not dump it into ice container

  • Customer: Danny from Martin GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the motor and everything is working great!

Ice maker stopped making ice - repair not successful

  • Customer: David from Lewisville TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the flapper door. I removed the screw to remove the wire connection. The ice maker slides out easily. I disconneted the power wires. Removed the motor cover. Removed the 3 phillips screws. Replaced everything in reverse order. I unplugged the unit to reset the LED panels. The ice maker is still not making ice.

Ice maker just quit working!

  • Customer: Keith from Sanford ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After my ice maker just quit working I did some troubleshooting based on the users manual. Found all the electronics to be working fine so I took out the ice maker to see if the water fill tube was frozen, it was not. Next I took off the motor access cover to discover the gear that rotates the spindle was pushed out further on it's drive shaft so it was not meshing with the motor drive gear. I pushed the white gear back on further only to discover the small locking tab on the shaft was broken off allowing the gear to slip outward and become unattached. Had to order a complete motor/gear assembly, installed in 20 minutes and all is fine again. Easy fix.

Ice maker stopped working

  • Customer: Stephen from Lynnwood WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching a YouTube video I was able to determine that my ice sensor was working properly. I was getting water through the door dispenser so I decided to pull the icemaker. First I removed the 2 hex head screws holding the ice door which gave me access to the icemaker. I removed the hex head screw holding the electrical plug cover on the bottom right side and removed it. I then pushed up on a plastic tab on the bottom left side of the ice maker and slid the icemaker out so I could access the electrical connection. After unplugging the electrical harness(plug/socket) I completely removed the icemaker from the freezer. The white square end cover easily pulled off the icemaker exposing the control and motor assembly. After removing the 3 screws holding the assembly on I pulled the assembly off the end of the icemaker. Installation was as simple as assembling the parts in reverse order making sure that the ice delivery male shaft "flat" mated with the "flat" on the motor drive female socket. After reassembly I went for a bike ride and when I returned about 3 hrs. later I was happy to see my icemaker was making ice again. This is actually easier than it sounds if you have any mechanical apptitude whatsoever.

Ice maker stop making ice cubes.

  • Customer: Ken from Nampa ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I saw the question listed on your website with your recommended part to repair. Instead of ordering a whole new ice maker I took the chance and ordered the recommended part for repair. I saw the video and when the part came it was really easy to replace. I only wish I had found your website earlier and not gone without ice for as long as I did. Thanks.

Plastic peice broke in the icemaker control

  • Customer: Brandon from New Brighton PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unpluged the refrigerator. Removed the cover on the control unit by inserting a screw driver under the metal clips. Removed the three screws frrom the front of the control unit. Pulled toward the back of the refrigerator on the metal loop which turns the icemaker on and off and it came loose where it goes into the control unit. Wiggled the unit and it came free. place the new unit in approximately the right position. Reached into the icemaker and moved the ice eject leavers so the shaft would enter the control unit with the flat side of the ejector in the right position. Gently pushed the control unit into its place and aligned the screw holes. Replaced the three screws. Inserted the wire shut off loop into the hole on the back of the control unit housing. Pluged in the electric. The ice maker worked.

Not making ice.

  • Customer: George from Palm Coast FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instructions on video on website. Very easy to do. Removed old part, put in new and it took all of 15-20 minutes. Had ice in approximately 1 hour.
All Instructions for the 10652603100
1,141-1,155 of 1,317