10651262105 Kenmore Refrigerator - Instructions

Fridge would stop cooling, get way over temperature. I noticed it would start up again if I tapped near the thermostat. It would run for a while then stop again. Replaced the thermostat exactly as shown in video. Fridge works fine now.

all is fine now. thanks andy

I just slid the old one out and slid the replacement in. Although PartSelect warned that the item was a substitute for the original drawer model, the crisper drawer supplied seemed identical to the original to me. I couldn't be more pleased.

watched the video followed the instructions and the repair took less than 30 mins. thank you parts plus for the video ref now workes properly and saved me a bundle of money

Remove icemaker, take off Icemaker control & motor ( 3 screws ) & install new part. Started making ice in less than 24 hours. Very happy customer.

I opened the box. That was the hardest part. I slid in the new drawer. I was a little distressed that my model # was not listed, but the pictures on your site were very helpful. Thanks

I removed the panel under the second self and backed out the 4 screws that held the motor in place. Disconnected the wireharness and removed the motor. Re attached the wire harness to the new motor and installed the new motor and screws. It still did not work so I did some more investigating in regards to this problem. It turns out that it may be the controller so I will have to order one.

Was surprisingly easy. Hardest part was taking the cover off the front to get access to the control bracket and switches. Can be done by prying two notches on underside of cover until they pop. Then slide up and off. Once off I could immediately tell the plastic clips on control bracket were broken. So replacing fixed that issue. My other issue was the ice dispenser door would not stay closed and sealed. I noticed that the plastic hook that holds metal dispenser pin in place was broken. Had trouble finding that part online so I superglued it in place and that has held it just fine. Now both my ice dispenser and water dispenser are working after buying a $10 part. This site is awesome. I am sure I would have paid $200 for this from a repairman.

First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

Remove drip pan from indoor ice dispensing system remove to bottom screws holding dispenser faceplate .lift faceplate out of the way exposing the bracket and ice and water dispenser micro switches be careful in removing microswitch, the one I removed came apart and had a little difficulty putting it back together ,used super glue and fix that problem. No instructions came with bracket so take your time. This is a relatively simple job any one should be able to do it.

My ice make had stopped working and I thought it was a water connection issue, however, after removing the motor cover, the plastic gear just fell to the floor. I wrote down the model number and looked the part up online. I ordered the part and it arrived a few days later. Three screws and a new motor and I had a working ice maker. Great experience.

removed old part and installed new part went smoothly with no headaches,. What a pleasant surprise.

slid and snapped the part in place

I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

The repair video indicated the removal of the entire ice maker when replacing the motor unit that I had ordered. Since I was replacing only the motor unit, located immediately to the front of the ice maker, made visible after removing the snap on cover, I chose not to remove the total unit and removed the old motor unit with the new one ordered and was successful with no further problems. I did turn the water off and disconnected the electrical plug of the fridge first. Three screws removed and replaced and done.