10651224100 Kenmore Refrigerator - Instructions

The disassembling and replacing the broken part went exactly as the directions.

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Followed the example on the video and everything fit in place without any problems. Only issue is that on a double door fridge the freezer is rather narrow so there isn't much room to work making it was a bit difficult to access the mounting screws.

Removed cardboard, Removed 4 bracket mounting screws, Removed plug, Removed screws securing motor to bracket. . Installed new motor on bracket, Installed fan on motor shaft , installed new pigtail on motor, Installed new assembled motor and bracket, Hooked up pigtail to electric supply, Installed cardboard, Plugged in to power supply and Voila, not even one foul word during the whole process. Note: watch the factory video. Thanks.

followed video instructions... only thing done differently was to tape crusher blades together before removing from shaft and added a drop of sewing machine oil to all screw sockets before replacing to reduce rusting and create greater ease of removal if further repairs needed

Really couldn't be easier. Loosen 3 screws that are easy to find. Disconnect the quick connect wiring harness. Now you have the old unit out. Take out the wire that tells if there is too much ice from the old unit and put it on the new one ( this was the hardest part of the project) Hook up the new wiring connector and hook it on the screws and tighten it up. Viola, your done. No messing with the water. Took me 5 minutes and I've never done it before.

TURN OFF WATER (if not already). Cut (or disconnect filler tube at bottom). Remove faceplate from refrigerator ice/water dispenser area. Remove screw holding metal bracket that holds water tube at filler point. Held metal mounting bracelet and pulled old filler tube out. Fed new filler tube thru bottom (hole is located at bottom of left door at hinge). As tube came out at top, pulled length needed to mount to new mounting bracket. Remounted new bracket (with hose attached) with new screw. Reconnected tube at bottom water line connection. Turn on water.

checked the close and open switch on front door first

I watched the installation video and did just like it said. It was pretty easy. My ice maker is working once again, and I'm pretty proud!

from the back of the freezer unscrewed the water feed to the feed tube. unscrewed the tube from the freezer and removed it. Ran hot water through the fill tube and then reinstalled the tube back into the freezer. Cycled the ice maker and the water started filling the icemaker. Did not use the water inlet valve that I ordered. Matter of fact.. I returned it. Always remember to check the fill tube and make sure it is not frozen.

I went on line to find the symptoms for what I was experiencing and went to web and entered the "KSRA" alphas and this list came up. I followed the explanation on video and it was identical. Good stuff.

Exactly as instructed by video on your site. The replacement took 10 minutes. thankyou Partselect.

I watched a couple of videos on your website about how to install a couple of parts that could possibly be causing the problem. Then I went and took the cover off of the area where the ice and water dispenser are in the door. I could tell from watching the videos which parts to look at to see where the problem might be. I figured out which part it was because I could see where it was broken. I then ordered the part. After I received the part I watched the videos again and then did the repair. VOILA! It worked. I put everything back together and the water dispenser was working. I was so pleased that I didn't have to call a repair man and I actually fixed it myself! My husband was so glad too.

I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.

The video provided excellent instructions on how to to this job. The hard part was removing the keeper ring so that the auger assembly could be separted from its housing.