10650794000 Kenmore Refrigerator - Instructions

I just slid the old one out and slid the replacement in. Although PartSelect warned that the item was a substitute for the original drawer model, the crisper drawer supplied seemed identical to the original to me. I couldn't be more pleased.

Remove icemaker, take off Icemaker control & motor ( 3 screws ) & install new part. Started making ice in less than 24 hours. Very happy customer.

I opened the box. That was the hardest part. I slid in the new drawer. I was a little distressed that my model # was not listed, but the pictures on your site were very helpful. Thanks

Was surprisingly easy. Hardest part was taking the cover off the front to get access to the control bracket and switches. Can be done by prying two notches on underside of cover until they pop. Then slide up and off. Once off I could immediately tell the plastic clips on control bracket were broken. So replacing fixed that issue. My other issue was the ice dispenser door would not stay closed and sealed. I noticed that the plastic hook that holds metal dispenser pin in place was broken. Had trouble finding that part online so I superglued it in place and that has held it just fine. Now both my ice dispenser and water dispenser are working after buying a $10 part. This site is awesome. I am sure I would have paid $200 for this from a repairman.

I was amazed how easy it was to replace this control board. I printed the pictures and instructions for the part that were on your site. There was a video for another part and it allowed me to get familiar with the layout of my unit. Thank you very much.

First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

Remove drip pan from indoor ice dispensing system remove to bottom screws holding dispenser faceplate .lift faceplate out of the way exposing the bracket and ice and water dispenser micro switches be careful in removing microswitch, the one I removed came apart and had a little difficulty putting it back together ,used super glue and fix that problem. No instructions came with bracket so take your time. This is a relatively simple job any one should be able to do it.

My ice make had stopped working and I thought it was a water connection issue, however, after removing the motor cover, the plastic gear just fell to the floor. I wrote down the model number and looked the part up online. I ordered the part and it arrived a few days later. Three screws and a new motor and I had a working ice maker. Great experience.

removed old part and installed new part went smoothly with no headaches,. What a pleasant surprise.

I surfed partselect and read that a reader had a similar problem with a rattling fan. I then removed the back panel, after I had unplugged the unit, and was able to feel the slop in the fan shaft. I then watched the video of how to replace the fan and ordered the part soon after. The part arrived 3 days later! Easy to do. I was finished in 12 minutes and the fridge runs silently. The part of the job that took the longest was vaccuming the undercarriage. There was alot of dust! Couldn't have helped the efficiency on the fridge. Keep it clean.

I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

The repair video indicated the removal of the entire ice maker when replacing the motor unit that I had ordered. Since I was replacing only the motor unit, located immediately to the front of the ice maker, made visible after removing the snap on cover, I chose not to remove the total unit and removed the old motor unit with the new one ordered and was successful with no further problems. I did turn the water off and disconnected the electrical plug of the fridge first. Three screws removed and replaced and done.

My ice machine stopped making ice I noticed the little dial under the cover stopped turning, so I bought the replacement part. It arrived three days later I un screwed the old one, and put the new in place and screwed it on the only little thing you might need to know is that the metal lever arm that moves up and down is attached to a plastic grommet with a two prong release that protrudes through the hole on the front of the assembly to release the old one just pinch them together. My ice machine works great now it was a very easy part to replace no need to call a repair service anyone with a screwdriver can replace this part

Per instructions in video. Super easy. Spent 45 min. cleaning ice/water dispenser and ice maker tray. Spent 15 min. replacing ice door.

There were excellent entries on the net of how to diagnose problem. Parts Select website had an excellent video on how to change part. Just followed instructions and changed parts in about 15 minutes. I am usually a klutz, but this was so easy