10650782001 Kenmore Refrigerator - Instructions

Very easy

After determining by the flashing light code what the problem was, I ordered the parts. Once the parts arrived, it took 15 minutes to install them by the instructions that came with them and two hours later I was making ice again. Very easy repair and there is a video on the website that shows exactly how to do it.

Package came in two days.I opened the box ,took the old draw out and slid the new draw in. Fixed in less than two minutes.I would definitely order from Parts Select again. Thanks for the prompt service

figured it was either the emitter/receiver or the control module.. even tho the online stats said it was probably the control module, i had a gut feeling (along with a volt/ohmeter) that said it was the emitter..... ordered the part.. came in 2 days..... six screws..... BOOM DONE !!fresh ice !!!!!ohhh what afeeling !!! pete s.

Watched the video provided, then followed that procedure. Everything now works fine, no more clicking.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

I took out the old drawer and inserted the new drawer in the same place! I wish all of life were that easy!

Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!

Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.

Opened the freezer door. Removed the ice bin from the freezer compartment. Removed with a nutdriver the two screws holding down the shaft holder (the triangular white plastic piece). Removed the shaft holder and the circular seal underneath. Pulled the hexagonal metal shaft up and out of the dispenser motor. Installed new circular seal and reinstalled the plastic shaft holder, etc..

I first viewed the instructional video provided by Partselect to pin point the faulty part. It was the control bracket. I would not have known how to expose the control bracket if it weren't for the video. Also Partselect said 48% of past water dispenser problems were the control bracket; this also helped me pinpoint the faulty part. I ordered the part; it arrived in 3 days. Using the video as a guide I repaired the dispenser in about 20 minutes start to finish. I will always go to Partselect for all appliance problems.

Open fridge....empty old drawer....through out old stuff....remove broken drawer and take downstairs to trash bin. Remove new drawer from package....open fridge. Insert new drawer. Restock with remaining items. Have a cold drink and congratulate yourself for a job well done!!!

Unplug appliance, turn off water supply valve to fridge. Remove rear cover and locate water inlet valve on lower right corner. Remove 2 screws holding valve in place. Pay attention to water line locations. Unplug 2 connections on valve. They are different size so you can't put them back on wrong. Remove all lines from bad valve. Cut all ends off lines and insert into new valve. Make sure they go where they belong. Press firmly into place. Reconnect electrical plugs and screw valve back in place. Turn water supply valve back on and check for leaks. If all is good put rear cover back on , plug appliance back in and your work is done. Easy replacement job.

Took out the broken drawer and replaced it with the new one. No problem at all.

I went to the PartSelect online videos and watched this one: "Refrigerator Repair - Replacing the Door Closing Cam (GE Part# WR2X4901)," to assess whether or not this could be a do-it-yourself repair. Even though the subject of the video was demonstrated on a refridgerator model different from mine, it appeared similar enough for me to get the idea of how to accomplish the repair, so I used the PartSelect site to guide me to the parts needed to do it. The parts came in and I once again watched the video and then proceeded with the repair. The repair was very simple and easily accomplished - took a half hour total. If you watch the video referred to above, you'll see exactly the way I did it. My experience precisely mirrored that shown in the video. One hint: I did spend some time wondering if I should have emptied the refridgerator before starting the job, and decided not to. It was the wise choice as the job went so fast, removing all the food would have been a waste of time. The door was off maybe 20 minutes total, and that was only enough time to raise the temperature inside about 5 degrees, which was quickly recovered when I re-installed the door. I can't say enough good about the PartSelect site, for the superb guidance in parts selection, as well as the extremely helpful how-to videos. I probably would not have attempted the repair on my own if not for the help this site provided. Thank you very much for this valuable service.