Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10650593003 > Instructions

10650593003 Kenmore Refrigerator - Instructions

All installation instructions for 10650593003 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10650593003
1,111-1,125 of 1,185
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water kept dripping out of water dispenser

  • Customer: Benjamin from Glens falls, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplug appliance, turn off water supply valve to fridge. Remove rear cover and locate water inlet valve on lower right corner. Remove 2 screws holding valve in place. Pay attention to water line locations. Unplug 2 connections on valve. They are different size so you can't put them back on wrong. Remove all lines from bad valve. Cut all ends off lines and insert into new valve. Make sure they go where they belong. Press firmly into place. Reconnect electrical plugs and screw valve back in place. Turn water supply valve back on and check for leaks. If all is good put rear cover back on , plug appliance back in and your work is done. Easy replacement job.

The Crisper Drawer Was Broken

  • Customer: Claudette from Tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out the broken drawer and replaced it with the new one. No problem at all.

The refridgerator door would not shut on its own. It had to be pushed completely shut every time it was opened.

  • Customer: Fred from Dacula, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went to the PartSelect online videos and watched this one: "Refrigerator Repair - Replacing the Door Closing Cam (GE Part# WR2X4901)," to assess whether or not this could be a do-it-yourself repair. Even though the subject of the video was demonstrated on a refridgerator model different from mine, it appeared similar enough for me to get the idea of how to accomplish the repair, so I used the PartSelect site to guide me to the parts needed to do it. The parts came in and I once again watched the video and then proceeded with the repair. The repair was very simple and easily accomplished - took a half hour total. If you watch the video referred to above, you'll see exactly the way I did it. My experience precisely mirrored that shown in the video. One hint: I did spend some time wondering if I should have emptied the refridgerator before starting the job, and decided not to. It was the wise choice as the job went so fast, removing all the food would have been a waste of time. The door was off maybe 20 minutes total, and that was only enough time to raise the temperature inside about 5 degrees, which was quickly recovered when I re-installed the door. I can't say enough good about the PartSelect site, for the superb guidance in parts selection, as well as the extremely helpful how-to videos. I probably would not have attempted the repair on my own if not for the help this site provided. Thank you very much for this valuable service.

Brooken Door Handel

  • Customer: David from Brecksville, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Its very easy all you have to do is slide the upper trim piece up and the lower trim piece down. That exposes 4 screws (2 top and 2 bottom) on the handle. Using a Philips screw driver remove the screws and the handle will come free. Put the new handle in place line up the holes and put the 4 screws in and tighten. Replace the the trim pieces and the job is done. It could be done in under 5 minutes including getting the screw driver and unpacking the box

small plastic part in the icemaker control assembly broke, disabling entire system

  • Customer: Linda from Baltimore, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the instructional video on the website. I found that my model was not exactly the same as the one in the video,completely removing the unit in order to switch parts was not possible or necessary.

Ice would not dispense through front of door. There was no sound when the lever was pushed either, however, the water dispenser next to it worked fine.

  • Customer: John from Cresskill, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove drip tray, remove two screws under drip tray and remove trim piece around dispensers. The micro switch is located at top right corner; slide it off the small post that holds it in place. Remove wire from switch (be gentle so you don't break wire, mine was on pretty tight. My switch was clearly burned out (black on connections). Anyway, just click wire back on new switch and push back on the post that holds it in place. Put back trim, screws and drip tray. The whole thing took a few minutes....I am no repair man but there were two switches on the post next to one another, I imagine the other controls the water dispenser in the event it had the same problem? If I had removed the trim piece and looked before ordering the part I probably would have swapped them out to confirm the problem was definitely the switch...I assume you could do that because they appear identical but can't say for sure. However, all indicators pointed to the switch anyway. Part was inexpensive and Part Select got it right out to me.

replace broken draw

  • Customer: SYLVESTER from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
First, I took out the broken unit,yhen I put in the new one..

Ice maker would not make ice

  • Customer: Daniel from Central, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the fridge and removed the cover from the Icemaker control assembly. Then remove the three phillips head screws, remove the Icemaker control. put the new control in place and use the three screws removed in previous step, replace the cover and plug the fridge back in. in a few hours you will have some ice.

icemaker stopped working

  • Customer: Patricia from Urbandale, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the icemaker control assembly and ice mold. Icemaker is working perfectly now. We replaced the ice mold (tray) because my husband read on the internet that the ice mold loses its nonstick coating and the ice sticks to the mold, and eventually burns out the control assembly.

Icemaker would not stop making ice.

  • Customer: Barry from Henderson, NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Purchased the recommended/required electronic control boards for the sender and receiver. Removed the units and replaced the boards and reinstalled. Icemaker is working fine since the repair.

Broken filter cap

  • Customer: Peggy from Estes Park, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Attached new one to filter...

broken drawer slides

  • Customer: Michael from Marietta, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replace drawe

Door wouldn't close fully, leaking cold air. light bulb went dead.

  • Customer: Mike from Sparks, NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the door (3 bolts on top). Removed the old plastic door closing cam on the bottom. Installed the new one. It was too tall (probably my fault), so I trimmed it with garden shears (it was a tubular piece of plastic). If you do this, be very careful, as the shears cut through the plastic MUCH easier than I thought. Popped the new one on, re-secured the door, and it works great now. Thank you partselect!

Not getting ice

  • Customer: linda from lambertville, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Replaced the optic boards - no lights working. Still no ice. No water coming into ice machine. Followed instructions on your website and diagnosed frozen line. Took ice machine out, used hair dryer, reinstalled and we have ice! Thank you so much for saving us a repair bill!!!!! Buying the part from you was very easy and your videos were excellent!!!

Not cold

  • Customer: Khoeuth from Germantown, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Get help from part select
All Instructions for the 10650593003
1,111-1,125 of 1,185