10650589000 Kenmore Refrigerator - Instructions

I got the new part and unplugged the refrigerator. I removed the wire auto shut-off. I removed the old motor assy. I checked to see if the motor quit running at the same locations as the new one before removing the entire ice maker. Lucky it did, so I installed the new motor assy without having to remove the ice maker. It took 10 minutes at the most.

I read the other replies and decided to replace the boards. It worked!!!! Ice right away!!! I would have only needed to chafe that if I didn't muscle the ice maker arms around in frustration and brek it!!! This website is great!! Parts came fast and accurate !!!! Thanks parts select !!! Another satisfied customer!!!

Set out an area large enough to lay the door down once I took it off the refrigerator. Took off the top screws and hinge. Had my 12 year old so help me with the door and hand me all the tools so I could quickly change out the parts and not leave the Refrigerator open for too long. I think from the moment we took the door off to the moment it was back on was probably about 5-6 minutes tops. That is how easy this was. All the parts fit and thank you to PartSelect and it great website that advised me of the second part that went with the first if not I would never have known. Thanks again!!

Verified that the sensors were working. After removing the Ice maker assembly from the sliding track, I found that the indexed drive wheel on the motor had broken off from the shaft mounting. I ordered the Icemaker control and motor assembly from Partselect and swapped out the bad part. It only has three screws to remove and replace so it's fast and easy to fix.

Water was not filling the ice tray and the ice tray coating was comming off. After the service repairman wanted to charge me over 500.00 for just replacing the ice maker, it told him to take a hike. I bought the icemaker and the electronic controls, which controls when and how much water goes into the tray for less than 250.00 and it took me less than 15 minutes to replace.

We were afraid of breaking the new part.But after watching the repair video about how much pressure to apply the part snapped right in. Thamk you for the video it helped alot.found the part quick and easy and it was shipped fast to us problem solved.

REMOVED three bolts holding the housing had a little trouble getting the housing out far enough to get the water lines back on that is when i had to use the needle nose.30 min at the most Thank You

Remove ice storage container from inside freezer. Remove philips screw from the coupler underneath ice storage container. Removed coupler and flat washer. Installed new plastic coupling and metal flat washers. Relaced original coupler and screw. Tighten screws very carefully. Installed ice storage container and filled it with fresh ice. Ice is now coming out when the level on the outside of the freezer door is pressed. Yeah...

The problem with our ice maker started when it stopped making ice. It was a hit or miss problem. One day it would make a bin full then couple days later none. One morning I noticed that there was water overflowing from the ice maker which froze inside the freezer. I ordered the maker and valve after watching the videos on this site. With those videos I was able to fix the problem in no time. Ice maker has been working properly for over a week now. My wife was ready to get a new fridge but I was stubborn and wanted to see if I could fix it. Thank you to partselect.com for the fast shipping and great instructional vids.

Pull the ice maker out using a nutdriver Pull the use a srew driver to remove the srews did the same to replace it put it back in had ice in 20 min

After googling for a parts supplier, PartSelect.com came up. The site was well done and had the Parts List conveniently available. I watched the associated video which was the highest quality "how-to" repair video I have seen. As it turns out, though, the icemaker does not have to be removed from the freezer unit. I removed the icemaker's shutoff lever, removed 3 screws, pulled the motor assy off, slid the new motor assy in place and re-installed 3 screws. Reinstalled the shutoff lever per the video and JOB DONE.

Ordered a new Ice Maker and replaced old one. The installation was a breeze except for the water recepticle on the right side of the Ice Maker. It was taller than the original and difficul to move the rubber water line into the new recepticle. Other than that. Problem solved. Been working great ever since.

First gasket received was damaged. Returned for full credit, no problem. Got second gasket and THEN found the real problem was the hinge! PartSelect accepted second gasket for full credit. No problem, no hassle. Awesome customer service. Thanks PartSelect!

This fridge is s ultraease 2 its 8 years old. Icemaker would'nt make ice. Its fairly easy all you do is take out the screws i recommend a power drill tho. Pop out the cover put the new motor in. I did'nt hear anyththing or see anything for a hour or two thought it did'nt work. Then i heard a clunk like ice falling into a bin. 3 hours later ice was falling frequently.

the icemaker stopped making ice. The cubes would get jammed up and finally just stopped all together. Removal of the icemaker and installation of the new one was pretty easy. The only problem was getting the electrical plug undone from the old unit. We have a lot of calcium in our water and I guess it finally ate through and ice was forming under the unit. It was five years old so not bad really. All is good....quick delivery. Thanks.