10650582001 Kenmore Refrigerator - Instructions

removed the damaged unit and inserted the replacement.

Openned both doors and removed lower grille. Closed doors and placed a piece of wood underneath door. The piece of wood slightly taller so that it supports and lifts the door while I worked. Working at the bottom of the door removed both upper and lower plastic cams and replaced with new ones. Be sure to tighten the single screw that holds down the plastic cam; if you leave them loose they will split/crack because they will move as you operate the door.

I vacuumed the back and underneath, hoping it will solve the problem, but after about 2 weeks of hoping I succumbed.... finding the proper wrench was the most time consuming. After removing the screws, the face plate removal was the most challenging. You have to pry the top part carefully away (we used a knife), after it just drops down. Used a flat screw driver to loosen the wire harness, after that the rest was less than child's play. We are still in the testing mode, but so far so good. Freezer freezes, ice maker drops the ice cubes (not melting), fridge is humming. Wish us good luck.

Replaces transmitter circuit board. Removed (3) screws and replaced board and replaced back into service. very easy!

Video made troubleshooting problem easy. I ordered the parts and 5 days later I had them. 10 minutes later they were installed and that night I had ice. This is the third appliance I have repaired using the partsselect video and replacement parts. All worked well. Much cheaper than getting a technician. Thank you. Cheap Guy!

Looked at drawing to see what sequence the parts went.

Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.

If you follow the video to the letter it's a piece of cake

Unscrewed water inlet support bracket,placed new inlet valve next to old valve with same orientation.one by one disconnected water lines and power leads and reconnected to same position on new valve.Reattached bracket and job done..Access to valve very easy.

Replaced the emitter and receiver boards by following the video instruction. Unscrew the cover plate, disconnect the wire, remove and replace the board and re-install. Repair was very easy and the unit is back in service.

1. Remove 3 phillips head screws with #2 phillips screwdriver. 2. Gently pull mounting bracket outward from freezer case. 3. Using fine needle nose pliers remove clip washer from lower end of flipper mounting rod. 4. Note position of flipper spring and pull mounting rod upward far enough to insert downward through new flipper and spring. 5. Install clip washer removed in step 2. Position assembly onto freezer cabinet and secure with screws removed in step 1.

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

took screwdriver, took out old parts. replaced with new parts. plugged fridge back in, turned on receiver. We have ice! Real Easy to install! Thank you Part Select.

The hardest part was figuring out how to get the front panel escutcheon panel off. With the putty knife under the bottom flange, you need to push down with some effort on the part of the flange where the drip pan slides in and twist the putty knife to disengage the locking tab. Once the panel is off, the rest of the job is easy with the aid of your video. Everything works like new...thanks.

Removed old valve. New valve does not provide for filter without modification. oOld valve used compression nut which had to be removed. Smooth cut with utility knife and push in. Needed a 1/4 inch compression coupling to hok up ice maker connection to 1/4 inch plastic hose fro the valve.