10650562991 Kenmore Refrigerator - Instructions

Turn the unit OFF - Removed one hex head screw on the bottom of the ice maker, removed the cable cover and unplugged. Removed front cover & Slide the icemaker out. Removed control cover and removed the three phillips head screws to the controller. Put the new controller back on with the three phillips head screws, pushed the cover back over the controller. Plugged the unit back in, then slide it back in the tracks, put the cable cover back on and installed the hex head screw, popped the front cover back on and turned the unit ON - DONE!

My dad and I worked together. The video helped but it was a little more complicated. If you can't find the water supply, remove the filter and water should stop, that's what we did. We had to remove the freezer door for access to the ice maker. It was tricky taking the icemaker off and getting it back on. Replacing the motor was easy, just as shown in the video. Just like others have said, within an hour of the repair the ice starting coming!

Thanks to this site, it told me what was wrong, what to order and how to repair it.

Remove front dust grill at bottom, pulls off with a little muscle.. While this is I found it to be a good time to vacuum area. Remove two screws at bottom in front with nut driver. Lift wire on left out. Hold filter unit and grasp water line and pull steadily repeat for other line. Remove old filter housing and reassemble. The worst was having to buy the whole part just for the keeper.

2 screws...removed old part Module Assembly..put in new and was set to go!

Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

I had to make sure the electronic beam was working properly, which it was (steady beam if you press in the side plastic flap. I also had to make sure the water valve for the icemaker was working properly as well, which it was by switching the lead wires on the valve (water dispenser wire to ice maker valve, and hitting water dispenser paddle and hearing water flow to the ice maker). After that, I knew it was the icemaker motor. Removed three screws with a socket, disconnected wire harness (had to use pliers to pull it apart), pulled out entire icemaker unit. Loosened three screws on motor control unit to remove it from icemaker unit, then inserted new motor control unit and re-screwed the 3 screws. Then I pu tthe entire icemaker unit back in the freezer, connected wire harness, re-inserted three screws and was finished. I then waited for one hour, went to check ice maker and I had ice cubes forming in the tray.

Followed the video on Parts Select and it was a breeze.

I have a side-by-side fridge/freezer, so taking out the icemaker is a bit more tricky than the video shows. I just unscrewed a nut in the back right of the mechanism (this nut is holding the icemaker in place as well as the plug cover). Once that was off it slid out pretty easy. Because the freezer is so narrow, it's a bit difficult to get it back in, but all told the repair took me about 20 minutes. Replacing this part fixed the icemaker immediately and we're so glad to have our on demand ice back! Ladies, don't be afraid of a little appliance repair!

Researched the problem on the internet. Identified the icemaker control and motor assembly as the most likely culprit. Ordered a new one. Arrived in two days. Installed it in about 15 minutes. Had ice 3 hours later.

I removed the ice maker, which consist of three 1/4 inch screws to install the water fill cup and bearing. One must loosen the front panel of ice maker to install the fill cup which consist of two standard screws, slide forward enough to install new fill cup. The removal of the Icemaker control was simple, using #2 phillips screwdriver and three screws. Unplug the control and install the new one, replace the three screws and cover. Reinstall the ice maker and within one hour cubes were dropping in the bin. I saved a lot of money repairing myself, which more than covers the shipping cost. Shipping was fast, two days.

Repaired by following the video with ease and was happy to see ice the next morning.Great service, price and advise .Thank you.

It took longer to get the part than it took to repair the water inlet. The help from the staff was very responsible and the repair direction off of the net very clear and understandable. I order the wrong part and was offered assistance and directed to the correct part than there were no issues but clear sailing.

follow instructions on web site to install motor module.Great web site. Saved me a lot of money.

Just followed the video that you guys had on line . It was a very easy repair