10650544001 Kenmore Refrigerator - Instructions

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

I removed the upper hinge cover and then the the hinge itself. Then lifted the door off the lower hinge peg. I placed a blanket on my pool table and positioned the door on it. The bottom screws were a little difficult to get the nutdriver seated so I used a quarter inch drive with socket to remove the screws. The replacement Closing Cam was quickly inserted and reassembled the hinge and lubricated with vaseline. Next I removed the Door Cam that was still on the peg on the refrigerator (it was completely worn flat). Quick work for this too. I tried to set the door back on the pivot hinge but eventually I needed another person to guide the door onto the peg. Reassembled the top hinge and voila, the door works just like new.

Simply slid the replacement into place. 30 seconds at most.

I just changed old drawer to new drawer

Drilled holes where pins had sheared off. Replaced pins with 4-40 x 1" screws and nuts and fastened switches and spacers on bracket. Used Loctite threadlocker to prevent nuts from loosening and installed bracket. So far, both ice and water dispensers are working fine.

My first try was to replace the water inlet valve. New valve was a good bit different than the original but not too hard to figure out. The main water inlet is on the inside rather than the outside. Flex hose and a stick in connector were included and I was able to work through that. But, when I turned it on the water still over flowed. The only thing left was the Ice maker. I ordered a new one. It came broken into several pieces. I ordered another, it arrived overnight with expediated shipping. install took maybe 15 minutes. problem solved. The company refunded me the full charge for the damaged ice maker and most of the charge for expediated shipping on the replacement. I'm happy and my wifes very happy.

I followed vidio instructions, took about 15 minutes. Fridge making great ice cubes again. Felt prouud of the repair I did being 70 years old and a female. Thank you

I watched the video on line and fixed as per the easy demonstration. Sad something 4 years old breaks.

First of all the part was not located in the section of the refrigerator that was shown in the video. I wasted a lot of time taking that section apart only to find that the part wasn't there. After some investigation I finally located the defective part. It was behind a piece of sheet metal that had to be bent out of the way to unscrew the part. If I hadn't bent it out of the way, it would have been a major disassembly to remove the sheet metal. Once removed, the installation of the new part was fairly simple. The only confusing thing about the installation was determinig which of the prongs on the part that the internal wire to the new part was to be attached. There were 3 options given and the instructions were not very clear as to which one I should use. Apparently I guessed correctly because the refrigerator seems to be functioning perfectly since the repair.

Removed old drawer, replaced with new one. Easy fix. New drawer fits perfect.

The glass cover came on time and in good packaging. I removed it from the packaging and slipped in to the shelf. It fit perfectly and was extremely easy to do. We are very pleased with the entire process. Thanks

After viewing video, took front cover off and found switch mounting broke. Ordered part through the online selector, which worked great. Received the part in a timely manner. Replace broken part, working great.

I took the ice maker right out

At first I just ordered a new motor and followed the instructions on the video . The new motor started working overtime but no water was being delivered to the tray . Ordered a new tray and re-installed. Working fine now. At first the ice was sticking, but that seems to have stopped now. It may be better to pull the ice maker out and check to see if there is damage to the tray before ordering. That way it could save the time of not doing things twice.

Replaced control and motor on the basis that most respondents found this unit to be at fault when the icemaker failed. Unfortunately, this wasn't the problem. Sudsequently, I replaced the electrionic boards which did fix the system. It would have been helpful (and less expensive) if the patrsselect website provided more help with problem diagnosis. Otherwise, the website is great!