10650512002 Kenmore Refrigerator - Instructions

Removed the door, removed the old lower door cam, and replaced with new cam.

Followed the Partselect instructions - removed door, removed old cam and replaced with new cam. One lesson learned. There are two cams - one that sits on hinge below door and one that is up inside bottom of door. If you are replacing one, replace them both.

Exactly as shown in the video; had a bit of trouble with the wiring harness, but all else went smoothly. If it were not for the explicit video installation instruction, it could not have been done by a do-it-yourself guy with tools. I had ice again in 3 hours! PartSelect is the absolute best when it comes to diagnosing, ordering and installing the part(s).

It was so simple, one screw to take the ice maker out and four screws for the motor. I ordered the motor because in your web site it suggested that 46% of the times its the motor the problem, I guess you could now say 47%. Got the part within 3 days. It was a pleasure doing business with your company. I recommended highly to everyone. Your web site was a lot of help.

With the help of the website I was able to verify that the part I removed (in the area of the clicking sound) was probably the part required for replacement. I ordered it, installed it... IT WORKS (I knew it the moment I plugged in the power cord and heard the compressor kick on). Saved me from buying a new fridge or calling a repairman. I'm a 58 year old woman with no appliance experience. I watched the videos and installed the part without any trouble. Thank you PartSelect for your easy to use website instructions and helpful hints.

I removed the door and switched out the cams on the bottom. Super easy. Door closes perfectly now.

1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

I did the repair, but apparently there's an Ice Door Kit with Bracket ( Part #8201756 - PartSelect Number PS990120 ) that has a metal bracket that will actually fix the problem with the broken plastic that holds the pin in.

After receiving the part, I watched the installation video on the PartSelect website. The step by step demonstration was excellent. I felt confident I could do it myself after watching the video just once, and utilizing the written instructions that came with the part. The installation went smoothly, and my refrigerator is functioning correctly again. Best of all, I did not have to go through the hassle and expense of hiring a repair person!

Insalled fan motor,problem went away. Thanks

He removed the front of the motor box. He then took the motor panel off and replaced it with the new one! So easy!! We have been buying ice or getting it from a friend that has a commercial ice maker. I could not believe it was that simple and the delivery was unbelievable. I ordered the part either Thursday or Friday and FedEx delivered it Saturday! Thank you so much. Now I have all the ice I need!!!

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

Part delivered within four days. It took all of 15 minutes to replace the icemaker after viewing the video. had a half a bucket of ice by morning thanks

Its the easiest repair in the world to do. Took less than 15 minutes. Removed the Icemaker unit from friedge, removed 3 screws replaced motor (very easy to do), 1 hr later I had Ice again! =)

I watched the video on how to make the repair. It was that easy. The hardest part was disconnecting the electrical. Once that was done it was a really simple fix.