10650512001 Kenmore Refrigerator - Instructions

Easy.... Video made replacment very smooth. I only needed one tool a nuy driver.

I saw a video of it, and simply took apart the ice maker and put the new Auger Drum in, then reassembled the ice maker.

The repair was easy. I wish I would have had a nutdriver; that would have made it extremely easy and a lot faster. I used a small wrench to take out the old ice maker. The new one went in easy. The arm was easy to move from the old ice maker to the new one, but it was a bit snug. We had to manually push the arm down a few times for the icemaker to dump the ice. After about 5 batches or so, it began to work on its own and now we have a full tub of ice (for the first time in two years). This was certainly time and money well-spent. Any one can do it!

Removed outer cover. Removed control bracket which holds the water/ice dispenser paddles. Removed paddles from old/broken bracket, plastic pins were broken where the paddles hinge. Placed on new bracket placed screws and it was done. Very simple repair. Part cost less then $18.00 including shipping. Saved me mucho dollars!!!!

hardest part getting the putty knife in right place to pop off cover---found the plastic bracket was broken where the switch was held in place---- so ordered new switches and bracket ---- got the parts in 3 days--good service--easy job 2 do and saved lots of $$$$$$$$---

I absolutely could not believe that the 2 bins we ordered arrived the 2nd day after I ordered them when I just used ground service! So nice to have usable bins again...and they snapped right in. Thanks for your prompt service.

The ice maker installation video was a life saver. Thank you. Followed video instructions and removal of old unit and installation of new unit took almost no time. Again thank you for the excellent video.

With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back

We changed the valves first to try it and then we changed the ice maker. That worked. Thank you nephew for helping me.

Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.

I watched your video and did just as he did. The video made it real easy and rather simple. It looked like it was going to be a mess until I watched the video.

Unplugged the refrigerator removed the cover and 3 screws. Pulled the old part off and replaced with the new and screwed it back on. Replaced the cover plugged it back in and it started working again.

I watched the short video at this website about replacing the bracket first. Then I replaced mine. Everything went smooth. No problems. Try it yourself.

i removed old door bin and replaced it with the new one. they are not attached with screws or bolts, they remove easily by pulling up and out.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.