Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
Below is a list of all parts for the Kenmore Refrigerator 10650504990. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.
The crisper drawer with humidity control is also known as the crisper drawer, and it is an easy part to replace in your refrigerator. The crisper drawer is found at the bottom of t...
The door bin may also be known as the door shelf bin and is a part for your refrigerator. The function of this bin is to fasten to the inside of your refrigerator door and act as a basket-style shelf. Normally this is a safe place for you to store jars, bottles, and canisters. This specific model is clear with a white trim around the top edge. Each one is sold individually and fits many side-by-side refrigerator models. No tools will be required for you to make this installation.
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...
The lower door closing cam is designed for use with refrigerators. It can be used on either the fresh food side, or the freezer side. It helps raise the door into position so the door can seal properly when closed. It also allows the door to easily swing open and closed. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace a door closing cam. To successfully install this part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. This replacement part is sold individually.
This clear convertible meat drawer can be used to store meats or vegetables. It has its own cold air duct to allow cold air from the freezer to flow into the drawer. You could have...
This ice and water filter fits all Whirlpool and KitchenAid refrigerators with a water filter located in the base grill, below the refrigerator door. This part will also fit any Kenmore models starting with 106. This filter is NSF certified, and is meant to filter for taste and odor, sediment, chlorine, and lead. The filtering provides overall better tasting and higher quality water. For best results, it is recommended to change your ice and water filter every six months or 200 gallons of filtered water. For better filtering, try the PS373105 filter. There are no tools required for this repair.
Note: This valve has been updated by the manufacturer and NO longer includes the removable pre-filter bracket connector. Must be ordered separately part number WPW10445062.
The lower door cam is also known as the closing cam or door closer cam and can be found on your refrigerator or freezer door. The purpose of the lower door cam is to lift the door to keep it from closing on the refrigerator/freezer liner. To do this repair you will need a 5/6 nut driver, a 5/16 socket and ratchet. For safety purposes, do not forget to turn off your appliance before making this repair. Note that this piece is black, and as per the manufacturer requires a new screw to mount the door cam which is sold individually.
This is a control bracket for your refrigerator, and may also be known as the dispenser control bracket. The function of this part is to be used as a fastener to hold the micro swi...
If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator does not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.
The icemaker control assembly is located in the freezer section of your refrigerator. It is what controls the icemaker. The control turns the timing cams and the ejector blades. It...
In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in the dispenser chute to let ice through when it is being dispensed. If you have the following symptoms such as: door sweating, difficulty opening or closing door, frost buildup, warm freezer section, or problems with ice dispensing, then this is a solution. The tools needed for this repair are a putty knife, needle nose pliers, and 1/4 inch nut driver. Wear work gloves to protect your hands when performing this repair.
This screw is sold individually.
This refrigerator defrost timer kit is designed to fix issues with your refrigerator temperature as well as symptoms such as the defrost cycle not working, build up of ice in the freezer, and unfamiliar noises from the timer. This device acts like a clock by continually switching between the cooling cycle and defrost heater, depending on the temperature of the refrigerator. If this part is not working, it can lead to temperature fluctuations in your refrigerator. Search for your model number to ensure the correct part is ordered. The tools used for this replacement is a 1/4 inch nut driver and Phillips head screwdriver.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.