10650504990 Kenmore Refrigerator - Instructions

At first I just ordered a new motor and followed the instructions on the video . The new motor started working overtime but no water was being delivered to the tray . Ordered a new tray and re-installed. Working fine now. At first the ice was sticking, but that seems to have stopped now. It may be better to pull the ice maker out and check to see if there is damage to the tray before ordering. That way it could save the time of not doing things twice.

Replaced control and motor on the basis that most respondents found this unit to be at fault when the icemaker failed. Unfortunately, this wasn't the problem. Sudsequently, I replaced the electrionic boards which did fix the system. It would have been helpful (and less expensive) if the patrsselect website provided more help with problem diagnosis. Otherwise, the website is great!

It was a very simple repair. The only frustration is that all I needed was a small plastic part on the motor assembly but had to buy the entire assembly. Glad that I found the assembly much cheaper on your site, but wish I could have just bought the small plastic part.

Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

I pulled the broken drawer out. I removed the screw in the existing stud with a phillips screw driver. I replaced that stud with the one I ordered and the new screw that came with it and I slid in the new drawer. Very easy. In fact the most difficult part was finding this website, but I've book marked it just in case I need more parts in the future. Thanks for the clearly marked photos on the website so I knew exactly what to order and for the quick delivery of my parts!

The customer service people did some cross checking and found a shelf and drawer that would work in my fridge. It did!! I love it now!!!Thanks for your help I did have to remove one of the selves - but now I have an extra!

I followed the video and was done with the replacement in less than 20 minutes. Just make sure after turning the water back on you check for leaks before you move the refrigerator back.

Package came in two days.I opened the box ,took the old draw out and slid the new draw in. Fixed in less than two minutes.I would definitely order from Parts Select again. Thanks for the prompt service

Watched the video provided, then followed that procedure. Everything now works fine, no more clicking.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

I took out the old drawer and inserted the new drawer in the same place! I wish all of life were that easy!

Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!

as per your video