10650452900 Kenmore Refrigerator - Instructions

removed the ice bin, removed small screw in bottom of grinder (visible from bottom). placed new coupling on shaft, inserted new screw and was finished. Super fast.

Followed instructions on this website. Only difference I placed a couple blocks under the door to keep it from dropping & removed both cams at the same time. No need to remove the door from the unit.

Ordered part from Parts Select at half the cost of other listing on www. Took 5 minutes and shelf fit perfectly.Thanks.Mike

Removed the old cam and put books under the door to hold it up. Follows instructions and really easy

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

I changed out the complete ice maker by first un-plugging fridge from the electrical outlet,then taking out the three screws holding the ice maker in place, unplugging electrical connector that operates the module and then removed by sliding ice maker away from fridge. Replaced old ice maker and re-plugged connector. Screwed ice maker back into place and plugged fridge back into outlet. Within 5 minutes we could hear the water dispenser filling the ice maker. Within another hour we had our first batch of ice.

I unloaded the door, removed the cap covering the screws at the top hinge. I removed the screws then lifted the door off the pin. Next I removed the screws holding the door cams in place. Replaced both cams and screws, set the door back on the pin then reinstalled the three screws at the top. Snapped back on the cover and I was done. Door works perfectly.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

The part arrived very quickly. I set up the laptop computer on the counter and started the instruction video (THEY ARE THE BEST!). With just a few starts and stops of the video during the installation in less than 15 minutes the repair was complete! The next day I had more ice than I needed. What a fabulous way to make appliance repairs at minimal cost! I will ALWAYS use PartSelect for any future repairs. I should also tell you that a 70 year old Woman did this repair - easily! If I can do it so can you!!

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Replaced Ice maker unit

I still have the parts, which look great. My son completely emptied to ice bin, de-iced the unit, cleaned the coupling.... it works.

Replacing the door closing cams, starts with emptying the door of all foodstuffs. Remove upper hinge cover. While supporting the door, remove three upper hinge screws with the nutdriver. Lift upper hinge from top and lift door off lower hinge pin. Remove the cam retaining screws on both the bottom of the door and the lower hinge pin. Pry (if needed) the worn cams from their position. Install new cams making sure to line up the screw holes. Re-install screws, tightening just snug. Lift door back onto lower hinge pin. Set upper hinge back in place with screws loosely installed. Check door gap, top to bottom to ensure proper alignment. Tighten upper hinge screws and re-install hinge cover. Check door for proper function.

I've replaced the door cams in the past, but they didn't last very long. I finally realized on my own that both parts need to be replaced at the same time. One piece is on the case-side of the bottom hinge and the mate is on the door-side of the bottom hinge. They both have a ramp shape, with door ramp riding up the hinge ramp as you open the door. The ramp shape makes the door want to slide back down the ramp to close automatically. These are plastic parts that wear out over time. If you don't replace both at the same time, the ramp shapes don't match and they wear out quickly. They are inexpensive parts, so always replace both at the same time. I added a thin layer of petroleum jelly to help them glide better. Hopefully this fix will last a long time. It's extremely easy. First take off the top hinge of the door. Then lift the whole door off the bottom hinge. You can set it on a chair with the bottom hinge hanging over the edge of the chair. Replace the two parts, one on the door bottom hinge and one on the refrigerator case bottom hinge. Easy as pie. The only tool needed is a nut driver. You need a helper to help lift and balance the door while you work on it.

After determining the control boards weren't working (by the light was not working) I replaced the control boards. By the way I received the parts in only a day and a half.It only took about 15 mins. The parts came with a troubleshooting guide witch was a little difficult to understand, but I got through it. The new parts were working but still not making ice. The water line had frozen. My wife and I took a meat injector as a syringe and injected hot water in the line and a air compressor I have and blew air into it also. It works again. As a tip try to blow air into the water line with your mouth to see if its clear.