10650449900 Kenmore Refrigerator - Instructions

I read the other replies and decided to replace the boards. It worked!!!! Ice right away!!! I would have only needed to chafe that if I didn't muscle the ice maker arms around in frustration and brek it!!! This website is great!! Parts came fast and accurate !!!! Thanks parts select !!! Another satisfied customer!!!

Set out an area large enough to lay the door down once I took it off the refrigerator. Took off the top screws and hinge. Had my 12 year old so help me with the door and hand me all the tools so I could quickly change out the parts and not leave the Refrigerator open for too long. I think from the moment we took the door off to the moment it was back on was probably about 5-6 minutes tops. That is how easy this was. All the parts fit and thank you to PartSelect and it great website that advised me of the second part that went with the first if not I would never have known. Thanks again!!

Water was not filling the ice tray and the ice tray coating was comming off. After the service repairman wanted to charge me over 500.00 for just replacing the ice maker, it told him to take a hike. I bought the icemaker and the electronic controls, which controls when and how much water goes into the tray for less than 250.00 and it took me less than 15 minutes to replace.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Remove ice storage container from inside freezer. Remove philips screw from the coupler underneath ice storage container. Removed coupler and flat washer. Installed new plastic coupling and metal flat washers. Relaced original coupler and screw. Tighten screws very carefully. Installed ice storage container and filled it with fresh ice. Ice is now coming out when the level on the outside of the freezer door is pressed. Yeah...

Ordered a new Ice Maker and replaced old one. The installation was a breeze except for the water recepticle on the right side of the Ice Maker. It was taller than the original and difficul to move the rubber water line into the new recepticle. Other than that. Problem solved. Been working great ever since.

First gasket received was damaged. Returned for full credit, no problem. Got second gasket and THEN found the real problem was the hinge! PartSelect accepted second gasket for full credit. No problem, no hassle. Awesome customer service. Thanks PartSelect!

the icemaker stopped making ice. The cubes would get jammed up and finally just stopped all together. Removal of the icemaker and installation of the new one was pretty easy. The only problem was getting the electrical plug undone from the old unit. We have a lot of calcium in our water and I guess it finally ate through and ice was forming under the unit. It was five years old so not bad really. All is good....quick delivery. Thanks.

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

I removed the upper hinge cover and then the the hinge itself. Then lifted the door off the lower hinge peg. I placed a blanket on my pool table and positioned the door on it. The bottom screws were a little difficult to get the nutdriver seated so I used a quarter inch drive with socket to remove the screws. The replacement Closing Cam was quickly inserted and reassembled the hinge and lubricated with vaseline. Next I removed the Door Cam that was still on the peg on the refrigerator (it was completely worn flat). Quick work for this too. I tried to set the door back on the pivot hinge but eventually I needed another person to guide the door onto the peg. Reassembled the top hinge and voila, the door works just like new.

The unit came out easily but the wire harness connector just didn't want to disconnect. The ice cold plastic was very difficult to work with and I had to use a screw-driver edge to pry it up and apart.

Unplugged refrigerator, took panels off each side of ice maker, unplugged bad components and replaced with new ones. Returned panels, plugged refrigerator back up. The ice maker began making ice almost immediately.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Watch replacement video then went from there. It was a simple replacement. Icemaker working and wife is happy:)

Remove ice unit to take out ice. Remove both boards and replace.Had to unplug refig to thaw out water line because it froze when unit would not make ice.