10650342010 Kenmore Refrigerator - Instructions

Open fridge....empty old drawer....through out old stuff....remove broken drawer and take downstairs to trash bin. Remove new drawer from package....open fridge. Insert new drawer. Restock with remaining items. Have a cold drink and congratulate yourself for a job well done!!!

Unplug appliance, turn off water supply valve to fridge. Remove rear cover and locate water inlet valve on lower right corner. Remove 2 screws holding valve in place. Pay attention to water line locations. Unplug 2 connections on valve. They are different size so you can't put them back on wrong. Remove all lines from bad valve. Cut all ends off lines and insert into new valve. Make sure they go where they belong. Press firmly into place. Reconnect electrical plugs and screw valve back in place. Turn water supply valve back on and check for leaks. If all is good put rear cover back on , plug appliance back in and your work is done. Easy replacement job.

Took out the broken drawer and replaced it with the new one. No problem at all.

Ordered the replacement filter cap. Received it, cut open plastic shipping envelope after unsuccessful attempts to tear envelope by hand, snapped cap in place; Wallaah, project completed successfully!!!

I received my new ice maker and got a nut driver and went to the freezer and removed my old ice maker . Then I noticed a problem. The cord on my old ice maker did not have a plug in the middle, my wires seemed to go through the wall of the freezer. I was afraid I would damage it if I tried to pull the wires from the wall, so I called customer service . She said I apparently ordered the wrong part. I had order a $70 unit and she said I needed the $114 kit. I would have to return the unit and order the kit. But she told me to look at the kit description and watch the repair video to see if that would help to see if I thought I could do it myself or get a service person. After looking at the parts and video I realized that the kit would be sending me the exact same unit and a couple of different type wire cords. I decided that all I needed to do was use the wire harness from my freezer and remove the new wire harness from the new ice maker unit. Of course I cut off the power to the refrigerator before pulling the plugs.I just had to loosen the two upper screws and remove the bottom screws, pull out the old unit, unplug the wire harness from the ice maker and removed the new wire harness from the new unit. Then I plugged the old wire into the new unit, slipped the unit back into position being certain that the water tube was in the proper position, tightened the upper screws, replaced the lower screw. I turned the power back on and waited. In a while I had ice again.

Remove drip tray, remove two screws under drip tray and remove trim piece around dispensers. The micro switch is located at top right corner; slide it off the small post that holds it in place. Remove wire from switch (be gentle so you don't break wire, mine was on pretty tight. My switch was clearly burned out (black on connections). Anyway, just click wire back on new switch and push back on the post that holds it in place. Put back trim, screws and drip tray. The whole thing took a few minutes....I am no repair man but there were two switches on the post next to one another, I imagine the other controls the water dispenser in the event it had the same problem? If I had removed the trim piece and looked before ordering the part I probably would have swapped them out to confirm the problem was definitely the switch...I assume you could do that because they appear identical but can't say for sure. However, all indicators pointed to the switch anyway. Part was inexpensive and Part Select got it right out to me.

removed cover unbolted thermo an replaced no big deal

First, I took out the broken unit,yhen I put in the new one..

Control panel in top of frig side removed and replaced, corrected issue with auto defrost and cooling of frig side. Remove two screws on inside top of frig just behind controls. Front cover of thermostat snaps off. Lower housing down to access control panel located inside housing. Two screws on bottom of housing should be removed to allow control panel removal. Unplug frig from power outlet while performing control module replacement. Unplug wire harness plugs from control module. Reverse procedure to install new module.

The reason it took me longer than what should have been a 15 minute repair is due to the fact that I could not figure out how the shaft came apart. I found an instructional video on Parts Select website that showed me that the shaft was held together by a reverse treaded, round nylon nut on the very front of the shaft. Just use a pair of pliers to grasp the nut and rotate it clockwise, after that you just need to lay the parts out in order as they come off the shaft so you can put it back together again.

This was a very easy repair and only took about 20 minutes. Unfortunately, after reordering, and installing the second motor, the intermittent noise is still there. Other than the occasional buzzing noise, that sounds like it is coming from the evaporator fan area, the refrigerator runs fine.

trip breaker. remove and save cover. loosen 2 top screws & remove bottom support bracket. unit slides up and out. unplug wire harness . attach new unit to wire harness. slip new unit in clearing fill spout. attach bottom support bracket and tighten top screws. replace cover and set breaker. CREATE REAL ICE!!

Simply follow the video instructions. Involves the removal of nine screws. to remove the old plastic sleeve cut the tube near the old thermostat and it slides of easily. Apply dish or hand washing soup to the new tube when putting the plastic sleeve onto the new probe. The hardest part is getting the end of the probe coiled to the right shape. Hey,` if I can do it with a broken collar bone, anybody should be able to do it.

I have not broken it but afraid to force the ice new ice guide into position. Crisper drawer no problem . Thank you

replace drawe