10650292010 Kenmore Refrigerator - Instructions

the tutorial is perfectwatch Steve. The boards were bad but coincidentaly so was the motor/control unit. I satrted with the boards, got my LED codes back to normal but still could not dispense. Installed the motor/control unit and had cubes dropping in 15 minutes. Great service, great tutorials.

The helpful Partselect video showed a slightly different model, as my icemaker uses optics instead of a bail for shutting off the icemaker. I ordered new optics based on a a customer description that, if the light on the right hand side of the freezer door jamb was blinking 2 flashes followed by a pause,it indicated that the optics were faulty, so I ordered and replaced them. This did not solve my problem. Then on-line I found further information that said I should close the flapper on the left side, and if the light was steady (which it was) the optics were OK. I then ordered the motor unit. I unscrewed the single screw under the right hand side of the track with a 1/4" nut driver, but found that sliding out the ice maker involved a little wiggling and prying, and, because it was awkward to disconnect the electrical connection, I found that it was not necessary to disconnect it. Then, after removing the end cap, it was a straight forward process to replace the motor, while adjusting the shaft to line up. Then,reverse all procedures and I now have ice. Success!

No repair needed, just replacement but I would like to say that you did a fantastic job getting it to me. I ordered the part at approximately 2PM and by noon the next day, it was at my front door. Thank you for shipping so quickly.

I ordered both the Ice maker and the control boards as It was for a rental and I did not want to make more trips then necessary to repair. I installed the new control boards and the ice maker and the refrigerator now makes ice.

Followed the lead of david from chesterfield in prying off out cover, unplugging it and setting it aside. Unscrewed and pulled out next assemply, and taped it above work area to avoid having to unplug. The pried pulled out pin to right holding ice door hinge to remove old unit. (Notice which way the spring faces before removing!) unplugged it. Ended up taking off push-dispenser handle (one screw on right) to get easier access. Then reinserted long pin being careful to have spring with two long tongs pointing down. Then put everything back together. Use all parts!

First I called Mr appliance from Bayport ny, And they told me we needed a new frig. So that night we went out and bought a new one from PC.The next day I canceled it and watched your video. The freezer side was cold and the fan was running so I figured it was most likely the defrost timer or the bimetel thermostat as the evaporator was frozen.I ordered the part from you (parts select)installed it EASY And it runs perfect!! This is my second time the last time it was my Moms frig but in this case the fan was not running. So I ordered from you watched your video and again it runs perfect. Thank you for all your help. I will always order from you.Oh and the part was at my door in two days.And I was able to cancel the other frig 1300.00 saved Thank you parts select

Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

Open refigerator took retaining plate off. Removed screws as instructed. Found timer. Replaced timer. Put parts back together.

I simply followed the step by step instructions demonstrated in the online videos for replacing the electronic control boards - emitter and receiver. Just that simple. 15 minutes later the repairs were completed. We've had ice ever since.

I checked the trouble shooting guide with the refrigerator and all signs pointed to the Electronic control boards that sense when the ice tray is full. After reading what other customer posted on this site I ordered the parts. I received the parts in two days time and had a harvest of ice within minutes of installing it. Thanks PartSelect. Scott

repair was not to bad. removed 3 screws, then unplug wire harness. The next thing i did was removed clip that holds pin. slid pin back enough to put new flipper in place. needs to go in front of spring.once in place slid pin back in and put clip holder back on. Then plug wire harness back in and 3 srews . done.

With the flat screwdrivers, table knife or something to pull the front cover, is not easy but it will come out, patient and kepp trying until you made it, the rest is easy.

Took old drawer out, put new drawer in. When I first opened the new drawer I was a little disappointed as the printing on the edge of the crisper (where it says humidity low-high) was a different color than my existing drawer, I know it's such a small detail that nobody would notice but me. My fridge is almost brand new and I'm the one who broke the drawer so I was a little sad but then realized that I could remove the edge of the drawer and replace it with my old one... VIOLA brand new drawer with purple letters! The drawer itself came so fast, I believe it was 1-2 days to my door! Thank you Part Select

took out old drawer, slid in new drawer and transfered food

The part arrived and we replaced both of the electronic control boards. Seemed fairly simple and immediately fixed the problem.