10650292010 Kenmore Refrigerator - Instructions

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

Followed the video supplied with shipment info from parts select. Simile and a great way to help the diy person. I will reyurn as a customer as well as pass the word. Thanks jhg

Been fighting this for over a year. Sometimes the fridge and freezer would heat up past the point it should come on. Had to slide the fridge temp control back and forth until the unit came on. Researched the problem determined the thermostat to be the issue. Got the part, finally found the time, then took the top tray out, popped off the escutcheon, unplug some wire and took out the control shuttle. Removed the old and replace with the new thermostat. Re-installed everything, plugged in it in and BAM. It's working. Now just fine tuning the slides to desired temps. THANKS PARTSELECT.

With the new Ice Guide all I had to do was a use a small screw driver to help guide the tabs into place and I was finished!

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

Removed (snap on)removed screw, and ice dispencer side (door and Pin) You have to assemble to reinstall (not easy to install while assembled) Install the pivot pin the rest of the way with the new spring mounted and when unit is almost in place, install the pivot the rest of the way, install tension hold downs that old both the water and ice dispenser shafts, reinstall cover, reconnect wiring and test, I had to remove the plunger because the water wouldn't shut off fast enough. Unit works great now.

After our four year old refrigerator door wouldn't stay closed as a do it yourself kinda gal I found this website that assisted me in an easy and inexpensive fix. The "plastic" yes, "plastic" piece on the bottom of the door was worn down to nothing. My only suggestion is to call in your order, the customer service folks will help you order the right cam for your model. The next thing is to change both cams if you have a side by side. We changed the fridge side which fixed the problem, then realized the cam on the freezer needed to be changed to make it level. Great customer service!

Simply washed the part and installed

Replaced the two circuit boards

Took the broken one out and put the new one in. I am a very skilled craftsman. ;-)

Replaced emitter and receiver boards. That did not fix the problem, ordered valve hope that is it.

Took the new chut set it into the ice dispensing openening,then cliped in place,End of repair.

Pulled out the old one an put the new one in. I was impressed with how easy it was to work with partselect.com, I had alway ordered through Sears before, but from now on I will be using partselct.com for ordering parts. Got the part in two days with free shipping and $20 les than Sears that did not have the part in stock.

SUPER EASY!!!! I pulled the old one out and put the new one in. Perfect fit and it took less than 60 seconds. This web site was about $30 cheaper than ordering from Kenmore and it was identical. I ordered my Crisper Pan on Wednesday and got it Friday. Highly recommended!!!!!!!!!

As your video showed. Used kitchen knife to get connection tight