10650269993 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
indtalled new part WPL W10190935 and it did not fix problem
-
Ronald from Jeffersonville, IN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker sounding like it was going to release ice, but not doing so.
This was the easiest repair I have ever done. Don't waste your money calling a repairmain for this one. Unplug from electrical outlet, and turn off water supply. I first removed the ice bucket to give myself the room needed to remove ice maker. Then I loosened to two top nuts holding the icemaker and removed the bottom one. Pulled the icemaker away from the freezer wall and disconected the power supply. Removed unit from freezer and removed the three screws holding control motor assembly in place, gently removed icemaker control assembly. Secured with the three screws, placed unit back in freezer making sure water inlet was in place and reconected power supply. Slid unit onto the top two nuts and tightened and replaced bottom screw. Turned on water supply and reconected to electrical supply. Easier then pie.
Parts Used:
-
Bridget from Clinton, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
popping sound when door opened beyond 90 degrees
I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.
Parts Used:
-
John from Westlake Village, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Icemaker stopped making ice
Removed the icemaker assembly, which was simple to remove. Once the assembly was removed, I unscrewed the motor housing and replaced it. I then reinstalled the assembly and closed the door. It did not making ice immediately and it took about 30 minutes to start.
Parts Used:
-
Bruce from Camarillo, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Our ice maker has not worked for years. My husband tried to repair it back then and now we know that he actually broke it. On the front of motor control there is a dial that says "DO NOT ROTATE'. It means do not rotate.
He removed the front of the motor box. He then took the motor panel off and replaced it with the new one! So easy!! We have been buying ice or getting it from a friend that has a commercial ice maker. I could not believe it was that simple and the delivery was unbelievable. I ordered the part either Thursday or Friday and FedEx delivered it Saturday! Thank you so much. Now I have all the ice I need!!!
Parts Used:
-
Linda from Colonial Beach, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ordered ejector arm.
No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.
Parts Used:
-
Joyce from Springfield, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker not working
Part delivered within four days. It took all of 15 minutes to replace the icemaker after viewing the video. had a half a bucket of ice by morning thanks
Parts Used:
-
philip from hazelton dr, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Crack on front of crisper pan
I cracked the crisper pan after having the refrigerator only one week and needed a replacement ASAP!! I was so happy to find this site and the part I needed. It's a little pricy for a plastic drawer but I can overlook that since it was in stock and I received it the very next day!!!I took out the cracked pan, slid in the new one and I was done!!!! No more unsightly crack!
Parts Used:
-
Kristine from Fort Worth, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice Maker stopped working
Its the easiest repair in the world to do. Took less than 15 minutes. Removed the Icemaker unit from friedge, removed 3 screws replaced motor (very easy to do), 1 hr later I had Ice again! =)
Parts Used:
-
Hector from San Diego, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Parts
My humidity control and veggie drawers were cracked and broken, I had shopped around but the price to replace them was too high and not in my budget. I came up on partselect.com while searching to find a more reasonable price. The price, service, delivery and customer service was outstanding. One of the drawer had been damaged during shipping, I called them and they sent another one free of charge right away. I had a very positive experience and I have added them to my favorite web sites.
Parts Used:
-
NADIA from GARNER, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice machine not working.
I watched the video on how to make the repair. It was that easy. The hardest part was disconnecting the electrical. Once that was done it was a really simple fix.
Parts Used:
-
Thomas from Naperville, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker stopped making ice
Unscrewed bolts pulled out motor,unhooked motor,replaced with new motor,put back in and replaced screws..fairly easy..then we had ice that evening!
Parts Used:
-
Vonnette from Bixby, OK
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Not making ice
-
Thomas from Orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Could not dispense filtered water, but ice worked
I found exact instructions on Youtube. Watched the video. Verified that my Control Bracket was in fact broken by partial disassembly. Ordered the part from PartSeclect. Received the part the next day (though I only paid for ground/standard delivery). Installed the part as described in the video using only two screwdrivers and needlenosed pliers within 14 minutes from start to dispensing water again. My water dispensing was interrupted less than 48 hours. Amazing!!! Thank you. It was fun, fun, fun.PaPa43
Parts Used:
-
PMichael from Villa Rica, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker stop working
turn power off, take the little cover on front of ice maker off so you can pull ice maker box out easier, unplug the easy connector ,after this take square cover off you'll see control motor take 3 screws off pull control motor out change new one in ,put them back together.turn power back on .then now Ice Maker will make some after 2 hours .You will SMILING then say ,Oh Yeah. QT good luck to everyone
Parts Used:
-
thuy from Houston, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!