10650262992 Kenmore Refrigerator - Instructions

Popped the cover off took panal off to access ice door screws.Removed old parts and replaced with new kit.Works fine now.

Removed the nut holding the plastic cover plate at the top of the door. Removed the 3 nuts holding the latch to the fridge. Lifted the door up and laid it on its' side. Removed the nut holding the door cam and replaced it with the new one. removed the nut holding the lower door cam and replaced it. Put a little vaseline on both cams and re-in-stalled the door. Took less than 15 minutes and the door is like new. Watching the video on the web site was perfect.

Removed food from door. Shut off fridge. Removed dust cap at top hinge. Marked location of top hinge with masking tape so lining up when reassembling would be easier. Removed screws holding top hinge to fridge. Removed door, placed on blanket&towel. Removed old door cam. Put on new door cam. Removed old hinge cam. Put on new hinge cam. Put door back on. Replaced top hinge, lining up with tape. Replaced dust cap. Note that door did not really self close very well until it was filled with food. By far the hardest part of the whole operation was that my wife wanted to clean the fridge in the process!

Removed flap and three screws holding tray. one screw holding plug protector. Slid tray out and unplugged . Removed three screws holding control & motor assembly.Put new unit in reassembled.

removed facial then the board replaced the lever retainer and reversed process very easy when part's are correct also shipping time fantastic good job 5 stars thank you

Watched video on Part Select, ordered part,it arrived in three days installed same fifteen minutes had ice within one hour.Saved $300.00.Thanks Part Select.

We used the video out on YouTube to show us how to replace the drum. It made the repair go so fast that we were amazed that two klutzes could do this repair! Remove the screws that hold the housing together. Place the screws in a cup to keep everything together. Remove the spiral unit and the plastic sleeve. The hardest part was removing the auger nut on the assembly. Just remember it is a left hand turn. After that, remember sequence of the blade assembly. The video suggested that you take a picture and that would help remembering the sequence of the blades. Follow the video!

Replaced with new ice machine. Three screws to take out ice machine, took off water lines put new one in. Could not be easier.

After I ordered the parts, which was very easy to do using this website I read the other comments in reference to this repair. I am in agreement with anyone that said patience is important! The repair went about as expected, the only thing I had to do different was, after I assembled the door, it would not activate. I checked the microswitches for the ice dispenser and found that the arm on the glass bracket was not hitting the switches. I shaved off part of the horn on the back of the arm and that solved the problem!

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

Just replaced the thermostat and is working perfectly. I would have to tap cooler knob and it would kick on. when it ran it ran well. So i knew it had to be electrical.Put in new thermostat and is working great!

Watched the video, followed the instructions, took my time and paid attention to what came off where, and viola. Not quite as easy as the guy in the video, but then it was my first time! Bottom line is: it worked. Refrigerator/freezer now maintains temperature exactly as expected, and I saved hundreds. Thank you!

I knew my ice maker was still working and I could hear that the switch on my water was still making the usual noise when tripped, so I knew that it had to be the inlet valve. I googled some videos and luckily found PartSelect.com. I used there diagnostics, looking at the percentages of other parts used to fix like problems. The part install was very easy as all I had to do was turn off the water and unplug the frig, remove the part, cut the input line and both output lines. Then slide those into the new part, with quick connects you just slide them in, the old part had compression fittings. Reattach the new part turn on the water, plug it back up, watch for leaks, your done..pretty sweet.

Did troubleshooting as manuel indicated. Had same problem once before. The replacement did the trick.

I simply followed the video on the partselect web site on my laptop while I did the replacement and it was easy! The online videos are the greatest way to do the repairs.