10650262991 Kenmore Refrigerator - Instructions

Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

I had to make sure the electronic beam was working properly, which it was (steady beam if you press in the side plastic flap. I also had to make sure the water valve for the icemaker was working properly as well, which it was by switching the lead wires on the valve (water dispenser wire to ice maker valve, and hitting water dispenser paddle and hearing water flow to the ice maker). After that, I knew it was the icemaker motor. Removed three screws with a socket, disconnected wire harness (had to use pliers to pull it apart), pulled out entire icemaker unit. Loosened three screws on motor control unit to remove it from icemaker unit, then inserted new motor control unit and re-screwed the 3 screws. Then I pu tthe entire icemaker unit back in the freezer, connected wire harness, re-inserted three screws and was finished. I then waited for one hour, went to check ice maker and I had ice cubes forming in the tray.

Followed the video on Parts Select and it was a breeze.

I have a side-by-side fridge/freezer, so taking out the icemaker is a bit more tricky than the video shows. I just unscrewed a nut in the back right of the mechanism (this nut is holding the icemaker in place as well as the plug cover). Once that was off it slid out pretty easy. Because the freezer is so narrow, it's a bit difficult to get it back in, but all told the repair took me about 20 minutes. Replacing this part fixed the icemaker immediately and we're so glad to have our on demand ice back! Ladies, don't be afraid of a little appliance repair!

Researched the problem on the internet. Identified the icemaker control and motor assembly as the most likely culprit. Ordered a new one. Arrived in two days. Installed it in about 15 minutes. Had ice 3 hours later.

I removed the ice maker, which consist of three 1/4 inch screws to install the water fill cup and bearing. One must loosen the front panel of ice maker to install the fill cup which consist of two standard screws, slide forward enough to install new fill cup. The removal of the Icemaker control was simple, using #2 phillips screwdriver and three screws. Unplug the control and install the new one, replace the three screws and cover. Reinstall the ice maker and within one hour cubes were dropping in the bin. I saved a lot of money repairing myself, which more than covers the shipping cost. Shipping was fast, two days.

Repaired by following the video with ease and was happy to see ice the next morning.Great service, price and advise .Thank you.

It took longer to get the part than it took to repair the water inlet. The help from the staff was very responsible and the repair direction off of the net very clear and understandable. I order the wrong part and was offered assistance and directed to the correct part than there were no issues but clear sailing.

follow instructions on web site to install motor module.Great web site. Saved me a lot of money.

Just followed the video that you guys had on line . It was a very easy repair

Repair was just like in the video, and the trouble shooting tips on here were great. The most highly probably issue for the broken bracket was exactly what my issue was. It was fixed in no time.Thanks, Tim

A local appliance parts distributor suggested that I go on line to get help figuring out the problem. The motor assembly was 51% probability. I ordered the part and followed the instructions given at the time of purchase. In a very short time ice was dropping.

Just watch video from part select and following the instruction to replace the control and motor assembly.

I removed the ice maker unit completely from the freezer, following a Utube repair video that I found. I originally thought it was just the control board that was defective, because on examination, found a burned-out copper trace on the board, as well as a burned-out plastic connection point. Installing the new parts was a breeze. This icemaker is pretty foolproof, with plastic tabs that line up with the housing. a matter of lining up the screw holes was all that was necessary. Only problem I had was attaching a plastic cover that shields the electrical connection from the water. Once all was installed, I had to wait overnight for the icemaker to make ice. We've had ice ever since! Thank you Partsselect for very courteous and fast service!

There are two tabs that hold the icemaker to the rails it sits on. I use a small screwdriver and pushed the tabs up to release the tray and slid the Ice maker out. the cover over the control motor just pops right off. Then I removed three screws from the control motor pulled it off and put the new on, replaced the screws and put the cover back on and slid the icemaker back into the rails. I shut the freezer door and within the five minutes it took me to put my tools back in the garage, it was dumping ice. Very easy to fix. You do not need to remove the screws that hold the icemaker to the tray.