10650262991 Kenmore Refrigerator - Instructions

Followed instructions in video and instructions by other home owners. Installation went very well. Parts Select shipped the repair kit. A good company to do business with. Saved a lot of money by doing the repair myself.

First of all, I am a female. So anyone can do this.I simple watched your video. Made the repair very simple. I was surprised that it really worked. I couldn't understand that if the door would still eject ice, why it wouldn't make the ice. It's the same motor. Anyway, It worked and I thank you very much. Very satisfied.

With brief instuctions it was very sraight forward. Three scews hold the motor assembly on. Ordered on a Sunday and the part was here the following Tues. Thanks Partselect

I unloaded the door, removed the cap covering the screws at the top hinge. I removed the screws then lifted the door off the pin. Next I removed the screws holding the door cams in place. Replaced both cams and screws, set the door back on the pin then reinstalled the three screws at the top. Snapped back on the cover and I was done. Door works perfectly.

Extremely simple especially after watching the video. Makes me think about why I did not attempt my own appliance repairs in the past. Big time savings! Thanks. P. S. excellent delivery service from Parts Select.

replaceed control motor assembly 3 screws took it off. then turned ice maker shaft by hand to line up key slot on new control unit . slid right together .ice started making within an hour . and the part got to my house the very next day after ordering awesome...

I watched the video so I had an idea of what to do. It was pretty straightforward. Turn off the water, take out the screws, line everything up, replace the part. It went smoothly and the icemaker is working again. :)

Unscrewed three screws, inserted new part, completed in less than 10 minutes and my icemaker works!!!! My icemaker did not work for 2 years and after spending $58, my icemaker was back in action.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

the part was very cheap and with the instructional video for replacement it was extremely easy to replace

Bracket pin that holds the water dispenser switch broke. Has to replace the whole bracket. Removed cover, unsnapped bracket, removed ice and water switches. Installed switches on new bracket, snapped in bracket, replaced cover. Ops check good. Very easy to do.

It was a easy enough repair. A little bit tough to press locks in to release hoses because lines were not long enough to pull out for under the refrigerator.

I had a problem with my ice dispenser not dispensing ice. The water worked fine but the ice side didn’t dispense ice. I watch the video on Parts Select.com and it was very helpful, but my model didn’t have screws to remove the front cover. At the bottom of the front cover was two indention where you could put a small tool and pry on it, I had to take a small pick tool and pry up on the front cover to pop it loose. You have to take something small like a pick tool because if you use something like a screwdriver or a butter knife you will get behind the plastic housing (also called a hood) that is screwed to the refrigerator. The key is to remove the face plate from the plastic hood piece (that is screwed to the refrigerator), so you have to get in between the face plate and the plastic housing. If you get behind the plastic housing you can break the housing, you must get between the two pieces and it will pop loose. This is the only problem I had with this installation. The rest of the repair was very easy and now my ice maker dispenses ice great.

Took old one out put new one in and its like new! Costs for a simple drawer was $75! Expensive but the transaction was simple!

I watched the installation video on "Parts Select". Unfortunately I watched it twice b/c the first part ordered last October only lasted 4 months. This part seems to be alright as the refrigerator has been running for approximately 6 days now - so far so good.