10650259000 Kenmore Refrigerator - Instructions

The repair video indicated the removal of the entire ice maker when replacing the motor unit that I had ordered. Since I was replacing only the motor unit, located immediately to the front of the ice maker, made visible after removing the snap on cover, I chose not to remove the total unit and removed the old motor unit with the new one ordered and was successful with no further problems. I did turn the water off and disconnected the electrical plug of the fridge first. Three screws removed and replaced and done.

My ice machine stopped making ice I noticed the little dial under the cover stopped turning, so I bought the replacement part. It arrived three days later I un screwed the old one, and put the new in place and screwed it on the only little thing you might need to know is that the metal lever arm that moves up and down is attached to a plastic grommet with a two prong release that protrudes through the hole on the front of the assembly to release the old one just pinch them together. My ice machine works great now it was a very easy part to replace no need to call a repair service anyone with a screwdriver can replace this part

Per instructions in video. Super easy. Spent 45 min. cleaning ice/water dispenser and ice maker tray. Spent 15 min. replacing ice door.

Watched your installation how to video. Applied same procedure. Went smoothly.

I had two repair problems. #1- Ice door kit & #2 control bracket. I followed the instructional video and completed repair in under 30 minutes. I surprised myself and had a happy wife.

Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

The hard part of the repair was getting the wife to empty the refrigerator door shelves. Once that was done simply removed the three screws on the door on the top of the door removed the bottom cam located on the bottom inside of the door. One of the simplest repairs I've ever done. Watching the you-tube video was a great help.

One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the components of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.

Removed outer cover. Removed control bracket which holds the water/ice dispenser paddles. Removed paddles from old/broken bracket, plastic pins were broken where the paddles hinge. Placed on new bracket placed screws and it was done. Very simple repair. Part cost less then $18.00 including shipping. Saved me mucho dollars!!!!

hardest part getting the putty knife in right place to pop off cover---found the plastic bracket was broken where the switch was held in place---- so ordered new switches and bracket ---- got the parts in 3 days--good service--easy job 2 do and saved lots of $$$$$$$$---

Followed instructions in video and instructions by other home owners. Installation went very well. Parts Select shipped the repair kit. A good company to do business with. Saved a lot of money by doing the repair myself.

First of all, I am a female. So anyone can do this.I simple watched your video. Made the repair very simple. I was surprised that it really worked. I couldn't understand that if the door would still eject ice, why it wouldn't make the ice. It's the same motor. Anyway, It worked and I thank you very much. Very satisfied.

With brief instuctions it was very sraight forward. Three scews hold the motor assembly on. Ordered on a Sunday and the part was here the following Tues. Thanks Partselect

I unloaded the door, removed the cap covering the screws at the top hinge. I removed the screws then lifted the door off the pin. Next I removed the screws holding the door cams in place. Replaced both cams and screws, set the door back on the pin then reinstalled the three screws at the top. Snapped back on the cover and I was done. Door works perfectly.

Extremely simple especially after watching the video. Makes me think about why I did not attempt my own appliance repairs in the past. Big time savings! Thanks. P. S. excellent delivery service from Parts Select.