10650229010 Kenmore Refrigerator - Instructions

pulled door off like video showed and undid the small bolts holding cams on and put new on. It was real easy. Thanks for youtube video

just sapped in place.

I ordered a new micro switch to do the repair. When I took face plate off the front of door two pieces of broken plastic fell out. Those pieces were part of what holds the switch in place, I need to order that part but I was able to use small tie wraps to hold switch in place and it has been working for a week now. The videos on this site are very helpful and gave me confidence to do the repair.

Pulled out old draw and inserted new one

I had already removed the ice container & realized the very end of the auger (drum) was broken. I still don't know why this part is plastic. I ordered the auger drum on Monday & received the part Wednesday morning by Fedex. I then retrieved your repair video by Steve on-line and paused it as I duplicated each step. The process was really very easy (I even surprised myself). The unit now works as it did when new. To think I went for over a month and the repair was so simple and inexpensive. Thanks also to your customer service rep who put my mind at ease that this was the correct part (My auger was totally plastic & different from the one in the illustration). He said if my model number said this part would fit, then it would and it did.

Easy as making toast.Super fast delivery,Less than 24 hrs.

First I removed the top bracket cover screw with a 5/16" nut driver. placing it aside, I removed the three screws holding the top door hinge off using a 5/16" socket on a 1/4 drive to free the screws , then continued to remove them with the nut driver. placing them aside on top of the refrigerator. Then I lifted the door up and off the lower hinge and laid the door down on my kitchen counter. I removed the lower hinge piece from the lower bracket still on the fridge with a 5/16" nut driver and installed the new piece in its place and also applied a few dots of Vaseline on the lower hinge piece, I then removed the screw and lower bracket from the door and installed the new one and also applied some Vaseline on this piece also. I also took a rag that had been dipped in olive oil and rubbed the entire gasket surround the door to lubricate the gasket to keep it soft, then I reinstalled the door back onto its lower bracket, and then lined door back up correctly and reinstalled the top mounting bracket and screws then the cover, and then tested door. Door opens now with no noise and opens easier also.

Watched your video pull the door off switched parts and all done . Thanks to your web site it helped me diagnose and fix the problem

I followed directions to take off the front of the water and ice maker then I saw the switch but I found out the plastic piece that held it in place was broke. I didn't order a new piece I used my reliable super duper quick glue and put the broken pieces to geter then put switch in place. then volla I had the water running like it did before. Thank you for telling me how to get the front off. That was the life saver.

I couldn't figure out if the front plate would come off so getting access to the screw to unscrew it was problematic at first. I don't have whatever tool you need to get at that angle so I used an Allen wrench with a 6.5 mm socket to unscrew the screw and replace the clip. After figuring that combination out it went really fast.

Be gentle when installing new plastic crisper drawer. If possible, read install instructions in Refrigerator Owner Booklet. Put new crisper drawer in position and gently push in until you are stopped by encountering the "stops" in side-support rails that are attached permanently to walls of refrigerator. Per Owner Booklet, lift new crisper drawer up slightly to pass over the "stops", then let the crisper drawer settle back down and push it in the rest of the way. Removal is reverse procedure. Be gentle!

I first ordered an inlet valve. It arrived EARLIER THAN PROMISED. I then went back online to check for installation tips. While reading tips for installing the inlet valve I read that the Ice Maker Controller accounts for 48% of failures. I performed the simple test you recommended by connecting the wires from the water dispenser coil to the inlet valve coil to determine if the inlet vale is working correctly. Sure enough, the valve allowed water to go to the ice maker. I immediately went back online and ordered a controller. The controller took about 30 minutes to install.

I took the ice bin and crusher down to find the problem. I needed a new auger. I did a Google search for the part and found instructions for taking the crusher mechanism apart. This went smoothly until I went to put it back together. I had to follow the instructions in reverse which was really difficult. I advise folks to use their cell phone camera to take close up pictures of the dismantling process . Use these to help you put it back together. All in all, I was very pleased and plan to return when another need arises. John (retired x 2)

Just like the video I watched online at your web site. piece of cake.!!

The water inlet valve was easy to replace. Just like the video shows. With one exception. I found the two metal brackets were tough to get apart because they were riveted together. So I took the drill with a 5/16 bit and drilled the rivet apart. It might have come apart without drilling but I was afraid of bending the brackets. You don't need to drill clear through both brackets. Just the clean the head of the rivet. It was quick and easy. The bit size is not important just so it is bigger than the rivet head.