10650037004 Kenmore Refrigerator - Instructions

Remove side handle from the freezer door ...pop out the black panel from the ice/water dispenser... you need to bend it a little bit to remove... un snap the electrical connections ...the plastic connectors, not from the fridge or the back of the panel,there are plastic connectors (white) in the middle between the fridge & the plastic outside panel.I needed a thin knife to lift the connector snaps to pull the pieces apart. It's not a bad idea to note how they match up so you can put it back properly. unscrew the white panel. There are two screws remove panel.I had to cut the micro switch out of the old style panel. the new panel is much more precise. By the way, if you are replacing the micro switch, it's a good thing to know, there are two. One is for the ice maker, the other is for the water dispenser. You might as well replace both at the same time even if one is working it will save you having to do this again anytime soon.Snap the micro chip into place & thread the wires back through the control panel screw the panel back into the door snap the wires togeather. now test the water dispenser just to be sure. Now arm wrestle the panel back in to the tracks. This is the hardest part. Why it doesn't just slide in is beyond me. Must have been designed by a guy!!! It really is easy & it saved me $300.

I checked the fuses and hoses in the back of the refrigerator to make sure water WAS in fact getting to the front of the fridge. Since the water through the front door worked fine, I had to check the water tube running to the ice maker. It was fine and water was waiting to go somewhere! I decided to pull the icemaker out of the fridge to see what I could fine. Once it was out, I took the ICEMAKER CONTROL AND MOTOR ASSEMBLY off (that's the side part with the dial on it). Only 3 screws to take that off, and it was EASY to see what was wrong once I took that off. There was a connection that was obviously bad (looked almost like it had burned out). My thought was that it was obvious what part was bad, what would it hurt for me to try to fix it myself? When I got online to find the part, PartSelect was the only one that I found that had the EXACT part that I needed, and lucky for me, there were multiple pictures of multiple angles of the part so I could compare and make sure I had the right one!! The part with shipping cost less than the cost of a repair tech to even come out and look at the fridge. Then add the cost of the part and labor if I had the repair tech fix it...I probably saved about $250!!!!

I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix.
I found you by googling appliance repair parts, and found your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron

First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install the new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.

Remove the knobs and faceplate to get at the screws behind it. Removing the sensor is a bit involved but everything else is fairly straight forward. See other postings for description / order of operation. Replacement took less than 30 minutes.
Works great now!

I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.

I took out the ice collection box and auger to get access to the three screws holding the ice maker assembly against the left wall of the freezer. You can use a screwdriver or a nut driver. I then unpluged the assembly and wiggled it loose from the water fill tube. I assumed that unplugging the unit would disable the water valve but I put a plastic tub under the fill tube just in case. I studied the assembly on the kitchen table for a few minutes before I disasembled it. After removing a snapon plastick cover I removed three or four screws on the gearbox and was able to pull and wiggle the parts apart. The heater contacts have rubber O rings so you have to be firm pulling the mould out of and into the gearbox mount. Make sure it is fully seated. On reassembly note that the ice kicking arm is notched so it fits into the gearbox only one way and it helps to have it in position when you screw the gearbox back on. I also found the plastic ice guide that fits on top of the mold a little awkward in snaping back together. Make sure its fingers space evenly with the ice kicking arms.

Switched Electric breaker to off. Removed all food and ice cube tray from freezer. Remove 4 screws on soleniod cover in rear of freezer. Removed two screws, two elec connectors from old soleniod and removed. Installed new soleniod. Reinstalled elec connectors and screws, ice cube tray and food. Turned breaker on . Ice maker worked properly.

I assumed the motor had burned out. I removed the 4 hex-head screws to remove the bracket holding the motor. I had to squeeze the electrical fitting to the motor located in the right rear of the compartment in order to electrically disconnect the motor, since the lower part of the fitting has a latch that prevents its easy removal. Then I could insert a vice grips on the shaft and on the coupling in order to (reverse) unscrew the coupling from the motor. I initially received the wrong replacement motor, but when the correct one arrived, it installed on the mounting bracket easily and I reinstalled the bracket with motor easily. It turns out a new motor did NOT fix the problem, so I'm not sure what to do now.

First I turned off my refrigerator, called for service, and had the problem diagnosed as a bad start relay. The repairman checked the compressor to see if it too was bad. The compressor was fine so I ordered the part I needed from PartSelect. After receiving the new start relay and overload from PartSelect, I unplugged the refrigerator, pulled it out and removed the screws from the lower back panel with the socket set and screwdriver. I removed the white self contained start relay box from the compressor by gently prying it off with a flat edge screw driver. I carefully disconnected the red and white wires from the broken start relay with pliers and followed the step by step directions that came with the replacement parts (the start relay and overload were separate components, not inside a self contained box like the original part). I proceeded to attach each part to the compressor, reconnect the red and white wires, and attach the new cover. I vacuumed out the area around the compressor and the condensor coils, plugged in the refrigerator, and turned it on. It worked immediately. I screwed the back cover on and pushed it back in place. Within 24 hours the ice maker was nearly full and I saved $225 by doing it myself.

Just removed the old timer and attached the wires to the new one and replaced the old. That simple!

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Found the control bracket housing had broken and micro switch for the water pump was not making contact with mechanical link. (In other words when you put a cup under the dispenser and push water did NOT come out.)

I removed the faceplate and switches, removed all the switches and installed them in the new control bracket. Installed new control bracket into fridge and tested. Works! Reinstalled faceplate and switches and drained system for a few minutes. Man I forgot how good filtered water tasted!

Removed food itmes on broken shelf. Removed old glass shelf cover. Removed broken shelf bracket. Installed new shelf bracket. Intalled new glass shelf cover. Replaced food items back on shelf

a simple replacement