10650027003 Kenmore Refrigerator - Instructions

Before I ordered, I followed the great video to disassemble the unit. That's when I realized I only needed to buy the drum. Five days later, I had the part. I thought I remembered how to reassemble it, but I ended up needing to watch the video again. It wasn't difficult, but you must get all the bits back in the same order!! Once that was dine, it all went together easily. Thank you! I'm so impressed with this site that I posted on Facebook about it so my friends can also save big bucks doing simple repairs themselves.

I first viewed the instructional video provided by Partselect to pin point the faulty part. It was the control bracket. I would not have known how to expose the control bracket if it weren't for the video. Also Partselect said 48% of past water dispenser problems were the control bracket; this also helped me pinpoint the faulty part. I ordered the part; it arrived in 3 days. Using the video as a guide I repaired the dispenser in about 20 minutes start to finish. I will always go to Partselect for all appliance problems.

The replacement ice maker came with a few different wiring harnesses which I assumed one of them would fit. well none of them did. I took the wiring off of the old one and matched up all of the receptacles and hoped for the best. It worked. The hardest part of the repair was dislodging the ice machine from the massive chunk of ice that had developed due to the leak in the old one. after that it was pretty easy. I hemmed and hawed about the wiring harness for a few minutes but felt confident it was going to be okay. I took the heat shield off of the old one and put it on the new one and used the control cover and the control arm from the old one too. I checked that all the holes and mounting assemblies matched up. I plugged in the wiring harness to the ice maker and than to the refridgerator, used a nut driver to secure it to the inside wall of the freezer with 3 screws, replaced the ice bucket and the cold air diverter and closed the door. Within an hour I heard the first ice hit the bottom of the bucket.

The unit was old so I opted to buy a new one even though it was just the motor. It took about 10 minutes to remove it after locating the fasteners, possibly less and about the same to install the new one. When the unit is turned on for the first time it does not start up right away. It will not start until it senses that it is cold enough in the freezer. For me that was about an hour to an hour and a half. There was a note on the cover that this could be as long as thirty six (36) hours. So don't be alarmed when it does not start running right away. The instructions were accurate.

I went to the PartSelect online videos and watched this one: "Refrigerator Repair - Replacing the Door Closing Cam (GE Part# WR2X4901)," to assess whether or not this could be a do-it-yourself repair. Even though the subject of the video was demonstrated on a refridgerator model different from mine, it appeared similar enough for me to get the idea of how to accomplish the repair, so I used the PartSelect site to guide me to the parts needed to do it. The parts came in and I once again watched the video and then proceeded with the repair. The repair was very simple and easily accomplished - took a half hour total. If you watch the video referred to above, you'll see exactly the way I did it. My experience precisely mirrored that shown in the video. One hint: I did spend some time wondering if I should have emptied the refridgerator before starting the job, and decided not to. It was the wise choice as the job went so fast, removing all the food would have been a waste of time. The door was off maybe 20 minutes total, and that was only enough time to raise the temperature inside about 5 degrees, which was quickly recovered when I re-installed the door. I can't say enough good about the PartSelect site, for the superb guidance in parts selection, as well as the extremely helpful how-to videos. I probably would not have attempted the repair on my own if not for the help this site provided. Thank you very much for this valuable service.

I watched the instructional video on the website. I found that my model was not exactly the same as the one in the video,completely removing the unit in order to switch parts was not possible or necessary.

Remove drip tray, remove two screws under drip tray and remove trim piece around dispensers. The micro switch is located at top right corner; slide it off the small post that holds it in place. Remove wire from switch (be gentle so you don't break wire, mine was on pretty tight. My switch was clearly burned out (black on connections). Anyway, just click wire back on new switch and push back on the post that holds it in place. Put back trim, screws and drip tray. The whole thing took a few minutes....I am no repair man but there were two switches on the post next to one another, I imagine the other controls the water dispenser in the event it had the same problem? If I had removed the trim piece and looked before ordering the part I probably would have swapped them out to confirm the problem was definitely the switch...I assume you could do that because they appear identical but can't say for sure. However, all indicators pointed to the switch anyway. Part was inexpensive and Part Select got it right out to me.

removed cover unbolted thermo an replaced no big deal

First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.

Unplugged the fridge and removed the cover from the Icemaker control assembly. Then remove the three phillips head screws, remove the Icemaker control. put the new control in place and use the three screws removed in previous step, replace the cover and plug the fridge back in. in a few hours you will have some ice.

Replaced the icemaker control assembly and ice mold. Icemaker is working perfectly now. We replaced the ice mold (tray) because my husband read on the internet that the ice mold loses its nonstick coating and the ice sticks to the mold, and eventually burns out the control assembly.

The reason it took me longer than what should have been a 15 minute repair is due to the fact that I could not figure out how the shaft came apart. I found an instructional video on Parts Select website that showed me that the shaft was held together by a reverse treaded, round nylon nut on the very front of the shaft. Just use a pair of pliers to grasp the nut and rotate it clockwise, after that you just need to lay the parts out in order as they come off the shaft so you can put it back together again.

This was a very easy repair and only took about 20 minutes. Unfortunately, after reordering, and installing the second motor, the intermittent noise is still there. Other than the occasional buzzing noise, that sounds like it is coming from the evaporator fan area, the refrigerator runs fine.

Simply follow the video instructions. Involves the removal of nine screws. to remove the old plastic sleeve cut the tube near the old thermostat and it slides of easily. Apply dish or hand washing soup to the new tube when putting the plastic sleeve onto the new probe. The hardest part is getting the end of the probe coiled to the right shape. Hey,` if I can do it with a broken collar bone, anybody should be able to do it.

This was a very easy fix. I utilized the short repair video for both parts and the entire install time was 40 min max. I installed both parts per the instructions, plugged the unit in and waited 20-30 minutes for the unit to reset itself. The Fridge cut back on and its running well within guidelines. In fact, it's cooler and running better than the last 6 months. Thank you "Part Select" for helping me save real dollars.